STA014 datasheet(16/45 Pages) STMICROELECTRONICS

16 / 45 page

6.1 - STA014 REGISTERS DESCRIPTION

The STA014 device includes 256 I

2C registers. In

this document, only the user-oriented registers

are described. The undocumented registers are

reserved. These registers must never be ac-

cessed (in Read or in Write mode). The Read-

Only registers must never be written.

The following table describes the meaning of the

abbreviations used in the I

2C registers descrip-

tion:

Symbol

Comment

Not Applicable

UND

Undefined

No Charge

Read Only

Write Only

R/W

Read and Write

R/WS

Read, Write in specific mode

VERSION

Address: 0x00 (00)

Type: RO

MSB

LSB

The VERSION register is read-only and it is used

to identify the IC on the application board.

IDENT

Address: 0x01 (01)

Type: RO

Software Reset: 0xAC

Hardware Reset: 0xAC

MSB

LSB

10101

100

IDENT is a read-only register and is used to iden-

tify the IC on an application board. IDENT always

has the value "0xAC"

PLLCTL

Address: 0x05 (05)

Type: R/W

Software Reset: 0xA1

Hardware Reset: 0xA1

MSB

LSB

XTO_

BUF

XTOD

OCLK

SYS2O

CLK

PPLD

XTI2DS

PCLK

XTI2O

CLK

UPD_F

RAC

UPD_FRAC: when is set to 1, update FRAC in

the switching circuit. It is set to 1 after autoboot.

XTI2OCLK: when is set to 1, use the XTI as input

of the divider X instead of VCO output. It is set to

0 on HW reset.

XTI2DSPCLK: when is to 1, set use the XTI as in-

put of the divider S instead of VCO output. It is

set to 0 on HW reset.

PLLDIS: when set to 1, the VCO output is dis-

abled. It is set to 0 on HW reset.

SYS2OCLK: when is set to 1, the OCLK fre-

quency is equal to the system frequency. It is

useful for testing. It is set to 0 on HW reset.

OCLKEN: when is set to 1, the OCLK pad is en-

able as output pad. It is set to 1 on HW reset.

XTODIS: when is set to 1, the XTO pad is dis-

able. It is set to 0 on HW reset.

XTO_BUF: when this bit is set, the pin nr. 28

(OUT_CLOCK/DATA_REQ) is enabled. It is set

to 0 after autoboot.

PLLCTL (M)

Address: 0x06 (06)

Type: R/W

Software Reset: 0x0C

Hardware Reset: 0x0C

PLLCTL (N)

Address: 0x07 (07)

Type: R/W

Software Reset: 0x00

Hardware Reset: 0x00

The M and N registers are used to configure the

STA014 PLL by DSP embedded software.

M and N registers are R/W type but they are

completely controlled, on STA014, by DSP soft-

ware.

STA014-STA014B-STA014T

16/45

STA014 数据表(PDF) 16 Page - STMicroelectronics

STA014 数据表(HTML) 16 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45

数据表下载

链接网址

STA014 数据表(PDF) 16 Page - STMicroelectronics

STA014 数据表(HTML) 16 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45

数据表 下载

链接网址

数据表下载