 |
数据搜索系统，热门电子元器件搜索 |
|
|
数据搜索系统，热门电子元器件搜索 |
|
ST7713 数据表(PDF) 29 Page - Sitronix Technology Co., Ltd. |
|
|
|||||||||||||||||||||||||||||
ST7713 数据表(HTML) 29 Page - Sitronix Technology Co., Ltd. |
|
|
29 / 159 page  ST7713 Ver 1.6 2008-05 29 9.3 6800-Series Parallel Interface (P68=’1’) The MCU uses one of following interface: 11-lines with 8-data parallel interface, 12-lines with 9-data parallel interface, 19-lines with 16-data parallel interface, or 21-lines with 18-data parallel interface. The chip-select CSX(active low) enables and disables the parallel interface. RESX (active low) is an external reset signal. The R/WX is the Read/Write flag and D[17:0] is parallel data bus. The LCD driver reads the data at the falling edge of E signal when R/WX= ‘1’ and Writes the data at the falling of the E signal when R/WX=’0’. The D/CX is the data/command flag. When D/CX=’1’, D[17:0] bits are display RAM data or command parameters. When D/C= ‘0’, D[17:0] bits are commands. The 6800-series bi-directional interface can be used for communication between the micro controller and LCD driver. The selection of this interface is done when P68 pin is high state (VDDI). Interface bus width can be selected with IM2, IM1 and IM0. The interface functions of 6800-series parallel interface are given in Table 9.3.1. Table 9.3.1 The function of 6800-series parallel interface P68 IM2 IM1 IM0 Interface D/CX R/WX E Function 0 0 ↓ Write 8-bit command (D7 to D0) 1 0 ↓ Write 8-bit display data or 8-bit parameter (D7 to D0) 1 1 ↓ Read 8-bit Display data (D7 to D0) 1 1 0 0 8-bit Parallel 1 1 ↓ Read 8-bit parameter or status (D7 to D0) 0 0 ↓ Write 8-bit command (D7 to D0) 1 0 ↓ Write 16-bit display data or 8-bit parameter (D15 to D0) 1 1 ↓ Read 16-bit Display data (D15 to D0) 1 1 0 1 16-bit Parallel 1 1 ↓ Read 8-bit parameter or status (D7 to D0) 0 0 ↓ Write 8-bit command (D7 to D0) 1 0 ↓ Write 9-bit display data or 8-bit parameter (D8 to D0) 1 1 ↓ Read 9-bit Display data (D8 to D0) 1 1 1 0 9-bit Parallel 1 1 ↓ Read 8-bit parameter or status (D7 to D0) 0 0 ↓ Write 8-bit command (D7 to D0) 1 0 ↓ Write 18-bit display data or 8-bit parameter (D17 to D0) 1 1 ↓ Read 18-bit Display data (D17 to D0) 1 1 1 1 18-bit Parallel 1 1 ↓ Read 8-bit parameter or status (D7 to D0) Note: applied for command code: DAh, DBh, DCh, 04h, 09h, 0Ah, 0Bh, 0Ch, 0Dh, 0Eh, 0Fh. 9.3.1 Write cycle sequence The write cycle means that the host writes information (command or/and data) to the display via the interface. Each write cycle (E low-high-low sequence) consists of 3 control signals (D/CX, E, R/WX) and data signals (D[17:0]). D/CX bit is a control signal, which tells if the data is a command or a data. The data signals are the command if the control signal is low (=’0’) and vice versa it is data (=’1’). Fig. 9.3.1 6800-Series Write Protocol Note: E is an unsynchronized signal (It can be stopped) |
|
链接网址 |
| ALLDATASHEET是否为您带来帮助? [ DONATE ] |
关于 Alldatasheet | 广告服务 | 联系我们 | 隐私政策 | 数据表链接 | 链接交换 | 制造商名单 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |
Chinese ▼
English
Chinese
German
Japanese
Russian
Korean
Spanish
French
Italian
Portuguese
Polish
Vietnamese
Indian
Mexican
British
New Zealand
