MPC8343ECVRADDB datasheet(14/79 Pages) FREESCALE

14 / 79 page

MPC8343EA PowerQUICC II Pro Integrated Host Processor Hardware Specifications, Rev. 10

Freescale Semiconductor

DDR and DDR2 SDRAM

Table 11 lists the PLL and DLL lock times.

DDR and DDR2 SDRAM

This section describes the DC and AC electrical specifications for the DDR SDRAM interface of the

MPC8343EA. Note that DDR SDRAM is GVDD(typ) = 2.5 V and DDR2 SDRAM is GVDD(typ) = 1.8 V.

The AC electrical specifications are the same for DDR and DRR2 SDRAM.

NOTE

The information in this document is accurate for revision 3.0 silicon and

later. For information on revision 1.1 silicon and earlier versions see the

MPC8343E PowerQUICC II Pro Integrated Host Processor Hardware

Specifications. See Section 22.1, “Part Numbers Fully Addressed by This

Document,” for silicon revision level determination.

6.1

DDR and DDR2 SDRAM DC Electrical Characteristics

Table 12 provides the recommended operating conditions for the DDR2 SDRAM component(s) of the

MPC8343EA when GVDD(typ) = 1.8 V.

Time for the MPC8343EA to turn on POR configuration signals with respect to the

negation of HRESET

1—

tPCI_SYNC_IN

1, 3

Notes:

1. tPCI_SYNC_IN is the clock period of the input clock applied to PCI_SYNC_IN. In PCI host mode, the primary clock is applied

to the CLKIN input, and PCI_SYNC_IN period depends on the value of CFG_CLKIN_DIV. See the MPC8349EA

PowerQUICC II Pro Integrated Host Processor Family Reference Manual.

2. tCLKIN is the clock period of the input clock applied to CLKIN. It is valid only in PCI host mode. See the MPC8349EA

PowerQUICC II Pro Integrated Host Processor Family Reference Manual.

3. POR configuration signals consist of CFG_RESET_SOURCE[0:2] and CFG_CLKIN_DIV.

Table 11. PLL and DLL Lock Times

Parameter/Condition

Min

Max

Unit

Notes

PLL lock times

—

100

μs—

DLL lock times

7680

122,880

csb_clk cycles

1, 2

Notes:

1. DLL lock times are a function of the ratio between the output clock and the coherency system bus clock (csb_clk). A 2:1 ratio

results in the minimum and an 8:1 ratio results in the maximum.

2. The csb_clk is determined by the CLKIN and system PLL ratio. See Section 19, “Clocking.”

Table 12. DDR2 SDRAM DC Electrical Characteristics for GVDD(typ) = 1.8 V

Parameter/Condition

Symbol

Min

Max

Unit

Notes

I/O supply voltage

GVDD

1.71

1.89

Table 10. RESET Initialization Timing Specifications (continued)

Parameter

Min

Max

Unit

Notes

MPC8343ECVRADDB 数据表(PDF) 14 Page - Freescale Semiconductor, Inc

MPC8343ECVRADDB 数据表(HTML) 14 Page - Freescale Semiconductor, Inc

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79

数据表下载

链接网址

MPC8343ECVRADDB 数据表(PDF) 14 Page - Freescale Semiconductor, Inc

MPC8343ECVRADDB 数据表(HTML) 14 Page - Freescale Semiconductor, Inc

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79

数据表 下载

链接网址

数据表下载