ADP1853ACPZ-R7 datasheet(18/28 Pages) AD

18 / 28 page

ADP1853

Data Sheet

Rev. 0 | Page 18 of 28

VIN PIN FILTER

It is recommended to have a low-pass filter at the VIN pin.

Connecting a resistor, between 2 Ω and 10 Ω, in series with

VIN and a 1 µF ceramic capacitor between VIN and AGND

creates a low-pass filter that effectively filters out any unwanted

glitches caused by the switching regulator. Keep in mind that

the input current could be larger than 100 mA when driving

large MOSFETs. A 100 mA across a 10 Ω resistor creates a 1 V

drop, which is the same voltage drop in VCCO. In this case, a

lower resistor value is desirable.

Figure 26. Input Filter Configuration

BOOST CAPACITOR SELECTION

Connect a boost capacitor between the SW and BST pins to

provide the current for the high-side driver during switching.

Choose a ceramic capacitor with a value between 0.1 µF and

0.22 µF.

INDUCTOR SELECTION

For most applications, choose an inductor value such that

the inductor ripple current is between 20% and 40% of the

maximum dc output load current.

Choose the inductor value by the following equation:

OUT

∆

−

where:

L is the inductor value.

fSW is the switching frequency.

VOUT is the output voltage.

VIN is the input voltage.

∆I

L is the peak-to-peak inductor ripple current.

Check the inductor data sheet to make sure that the saturation

current of the inductor is well above the peak inductor current

of a particular design.

OUTPUT CAPACITOR SELECTION

For maximum allowed switching ripple at the output, choose an

output capacitor that is larger than

)

(

ESL

ESR

OUT

−

∆

−

∆

≅

where:

∆V

OUT is the target maximum output ripple voltage.

∆I

L is the inductor ripple current.

RESR is the equivalent series resistance of the output capacitor

(or the parallel combination of ESR of all output capacitors).

LESL is the equivalent series inductance of the output capacitor

(or the parallel combination of ESL of all capacitors).

The impedance of the output capacitor at the switching

frequency multiplied by the ripple current gives the output

voltage ripple. The impedance is made up of the capacitive

impedance plus the nonideal parasitic characteristics, the

equivalent series resistance (ESR), and the equivalent series

inductance (ESL).

Usually the capacitor impedance is dominated by ESR. The

maximum ESR rating of the capacitor, such as in electrolytic

or polymer capacitors, is provided in the manufacturer’s data

sheet; therefore, the output ripple reduces to

ESR

OUT

∆

≅

∆

Electrolytic capacitors also have significant ESL, on the order

of 5 nH to 20 nH, depending on type, size, and geometry. PCB

traces contribute some ESR and ESL, as well. However, using

the maximum ESR rating from the capacitor data sheet usually

provides some margin such that measuring the ESL may not be

required.

In the case of output capacitors where the impedance of the

ESR and ESL are small at the switching frequency, for instance,

where the output capacitor is a bank of parallel MLCC capaci-

tors, the capacitive impedance dominates, so the output

capacitance must be larger than

OUT

∆

≅

Make sure that the ripple current rating of the output capacitors

is greater than the maximum inductor ripple current.

To meet the requirement of the output voltage overshoot during

load release, the output capacitance should be larger than

)

(

OUT

OVERSHOOT

OUT

STEP

OUT

−

∆

≅

where:

∆VOVERSHOOT is the maximum allowed overshoot.

Select the largest output capacitance given by either of the

previous two equations.

VIN

AGND

Ω TO 10Ω

1µF

ADP1853

ADP1853ACPZ-R7 数据表(PDF) 18 Page - Analog Devices

ADP1853ACPZ-R7 数据表(HTML) 18 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28

数据表下载

链接网址

ADP1853ACPZ-R7 数据表(PDF) 18 Page - Analog Devices

ADP1853ACPZ-R7 数据表(HTML) 18 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28

数据表 下载

链接网址

数据表下载