MC34708 datasheet(36/159 Pages) FREESCALE

36 / 159 page

Analog Integrated Circuit Device Data



Freescale Semiconductor

MC34708

Functional Block Description

The following are text descriptions of the power states of the system for additional details of the state machine to complement

the drawing in Figure 6. Note that the SPI control is only possible in the Watchdog, On and User Off Wait states and that the

interrupt line INT is kept low in all states except for watchdog and on.

7.5.2.1

Coin Cell

The RTC module is powered from either the battery or the coincell, due to insufficient voltage at VALWAYS, and the IC is not in

a Power Cut. No Turn On event is accepted in the Coin Cell state. Transition out (to the Off state) requires VALWAYS restoration

with a threshold above UVDET. RESETB and RESETBMCU are held low in this mode.

The RTC module remains active (32 kHz oscillator + RTC timers), along with VALWAYS level detection to qualify exit to the Off

state. VCOREDIG is off and the VDDLP regulator is on, the rest of the system is put into its lowest power configuration.

If the coin cell is depleted (VSTRC drops to 0.9 - 0.8 V while in the Coin Cell state), a complete system reset will occur. At next

power application / Turn On event, the system will startup reinitialized with all SPI bits including those that reset on RTCPORB

restored to their default states.

7.5.2.2

Off (with good battery)

If the supply VALWAYS is above the UVDET threshold, only the IC core circuitry at VCOREDIG and the RTC module are

powered, all other supplies are inactive. To exit the Off mode, a valid turn on event is required. No specific timer is running in this

mode. RESETB, RESETBMCU are held low in this mode.

If the supply VALWAYS is below the UVDET threshold, no turn on events are accepted. If a valid coin cell is present, the core

gets powered from LICELL. The only active circuitry is the RTC module and the detection VCORE module powering VCOREDIG

at 1.5 V.

If there is a USB supply or Charger inserted, the IC circuitry at VCORE, VCOREDIG, and the RTC Module will be powered up.

To exit the OFF mode, a valid turn ON event is required.

7.5.2.3

Cold Start

Cold Start is entered upon a Turn On event from Off, Warm Boot, successful PCUT, or a Silent System Restart. The first 8.0 ms

is used for initialization which includes bias generation, PUMSx configuration latching, and qualification of the input supply level

BP. The switching and linear regulators are then powered up sequentially to limit the inrush current; see the Power Up section

for sequencing and default level details. The reset signals RESETB and RESETBMCU are kept low. The Reset timer starts

running when entering Cold Start. The Cold Start state is exited for the Watchdog state and both RESETB and RESETBMCU

become high (open drain output with external pull-ups) when the reset timer is expired. The input control pins WDI, and

STANDBY are ignored.

7.5.2.4

Watchdog

The system is fully powered and under SPI control. RESETB and RESETBMCU are high. The Watchdog timer starts running

when entering the Watchdog state. When expired, the system transitions to the On state, where WDI will be checked and

monitored. The input control pins WDI and STANDBY are ignored while in the Watchdog state.

7.5.2.5

On Mode

The system is fully powered and under SPI control. RESETB and RESETBMCU are high. The WDI pin must be high to stay in

this mode. The WDI IO supply voltage is referenced to SPIVCC (normally connected to SW5 = 1.8 V); SPIVCC must therefore

remain enabled to allow for proper WDI detection. If WDI goes low, the system will transition to the Off state or Cold Start

(depending on the configuration; refer to the section on Silent System Restart with WDI Event for details).

7.5.2.6

User Off Wait

The system is fully powered and under SPI control. The WDI pin no longer has control over the part. The Wait mode is entered

by a processor request for user off by setting the USEROFFSPI bit high. This is normally initiated by the end user via the power

key; upon receiving the corresponding interrupt, the system will determine if the product has been configured for User Off or

Memory Hold states (both of which first require passing through User Off Wait) or just transition to Off.

MC34708 数据表(PDF) 36 Page - Freescale Semiconductor, Inc

MC34708 数据表(HTML) 36 Page - Freescale Semiconductor, Inc

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表下载