BM71BLE01FC2 datasheet(55/64 Pages) MICROCHIP

55 / 64 page

 2015-2016 Microchip Technology Inc.

DS60001372D-Page 55

BM70/BM71

Transmitter Antenna (from Section 8.3, RSS-Gen,

Issue 4, November 2014): User manuals for transmit-

ters shall display the following notice in a conspicuous

location:

The preceding notice may be affixed to the device

instead of displayed in the user manual.

A.2.2

RF EXPOSURE

All transmitters regulated by IC must comply with RF

exposure requirements listed in RSS-102 - Radio Fre-

quency (RF) Exposure Compliance of Radio communi-

cation Apparatus (All Frequency Bands).

A.2.3

HELPFUL WEB SITES

Industry Canada: http://www.ic.gc.ca/

A.3

Europe

The BM70/BM71 is an R&TTE Directive assessed

radio module that is CE marked and has been manu-

factured and tested with the intention of being inte-

grated into a final product.

The BM70/BM71 has been tested to R&TTE Directive

1999/5/EC Essential Requirements for Health and

Safety (Article (3.1(a)), Electromagnetic Compatibility

(EMC) (Article 3.1(b)), and Radio (Article 3.2) and are

summarized in Table A-1/Table A-2. A Notified Body

Opinion has also been issued.

The R&TTE Compliance Association provides guid-

ance on modular devices in the document “Technical

Guidance Note 01”

which is available for download

from the following location:

http://www.rtteca.com/html/download_area.htm.

A.3.1

LABELING AND USER

INFORMATION REQUIREMENTS

The label on the final product which contains the

BM70/BM71 must follow CE marking requirements.

The R&TTE Compliance Association Technical Guid-

ance Note 01

provides guidance on final product CE

marking.

A.3.2

ANTENNA REQUIREMENTS

From the R&TTE Compliance Association document

Technical Guidance Note 01.

Under Industry Canada regulations, this radio trans-

mitter may only operate using an antenna of a type

and maximum (or lesser) gain approved for the trans-

mitter by Industry Canada. To reduce potential radio

interference to other users, the antenna type and its

gain should be so chosen that the equivalent isotrop-

ically radiated power (e.i.r.p.) is not more than that

necessary for successful communication.

Conformément à la réglementation d'Industrie Can-

ada, le présent émetteur radio peut fonctionner avec

une antenne d'un type et d'un gain maximal (ou

inférieur) approuvé pour l'émetteur par Industrie Can-

ada. Dans le but de réduire les risques de brouillage

radioélectrique à l'intention des autres utilisateurs, il

faut choisir le type d'antenne et son gain de sorte que

la puissance isotrope rayonnée équivalente (p.i.r.e.)

ne dépasse pas l'intensité nécessaire à l'établisse-

ment d'une communication satisfaisante.

To maintain conformance to the testing listed in

Table A-1/Table A-2: European Compliance Testing,

the module shall be installed in accordance with the

installation instructions in this data sheet and shall

not be modified.

When integrating a radio module into a completed

product the integrator becomes the manufacturer of

the final product and is therefore responsible for

demonstrating compliance of the final product with

the essential requirements of the R&TTE Directive.

Provided the integrator installing an assessed radio

module with an integral or specific antenna and

installed in conformance with the radio module man-

ufacturer's installation instructions requires no further

evaluation.Under Article 3.2 of the R&TTE Directive

and does not require further involvement of an

R&TTE Directive Notified Body for the final product.

[Section 2.2.4]

BM71BLE01FC2 数据表(PDF) 55 Page - Microchip Technology

BM71BLE01FC2 数据表(HTML) 55 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64

数据表下载