TMS320DM6431 datasheet(64/227 Pages) TI1

64 / 227 page

3.4.1

Boot Modes

TMS320DM6431

Digital Media Processor

SPRS342C – NOVEMBER 2006 – REVISED JUNE 2008

www.ti.com

There are several methods by which the memory and register initialization can take place. Each of these

methods is referred to as a boot mode. The boot mode to be used is selected at reset. For more

information on the bootmode selections, see Section 3.4.1, Boot Modes.

The device is booted through multiple means—primary bootloaders within internal ROM or EMIFA, and

secondary user bootloaders from peripherals or external memories. Boot modes, pin configurations, and

The DM6431 boot modes are determined by these device boot and configuration pins. For information on

how these pins are sampled at device reset, see Section 6.5.1.2, Latching Boot and Configuration Pins.

• BOOTMODE[3:0]

• FASTBOOT

• AEM[2:0]

• PLLMS[2:0]

Note: The PLLMS[2:0] configuration pins are actually multiplexed with the AEAW[2:0] configuration pins.

For more details on the multiplexed AEAW[2:0]/PLLMS[2:0] configuration pins and control, see

Section 3.5.1.2, EMIFA Address Width Selects (AEAW[2:0]) and FASTBOOT PLL Multiplier Selects

(PLLMS[2:0]).

BOOTMODE[3:0] determines the type of boot (e.g., I2C Boot or EMIFA Boot, etc.). FASTBOOT

determines if the PLL is enabled during boot to speed up the boot process.

The combination of AEM[2:0] and PLLMS[2:0] is used by bootloader code to determine the PLL multiplier

used during fastboot modes (FASTBOOT = 1).

The DM6431 boot modes are grouped into three categories—Non-Fastboot Modes, Fixed-Multiplier

Fastboot Modes, and User-Select Multiplier Fastboot Modes.

• Non-Fastboot Modes (FASTBOOT = 0): The device operates in default PLL bypass mode during

boot. The Non-Fastboot bootmodes available on the DM6431 are shown in Table 3-5.

• Fixed-Multiplier Fastboot Modes (FASTBOOT = 1, AEM[2:0] = 001b): The bootloader code speeds

up the device during boot according to the fixed PLL multipliers. The Fixed-Multiplier Fastboot

bootmodes available on the DM6431 are shown in Table 3-6.

Note: The PLLMS[2:0] configurations have no effect on the Fixed-Multiplier Fastboot Modes, as these

pins function as AEAW[2:0] to select the EMIFA address width when AEM[2:0] = 001b.

• User-Select Multiplier Fastboot Modes (FASTBOOT = 1, AEM[2:0] = 000b and 101b): The

bootloader code speeds up the device during boot. The PLL multiplier is selected by the user via the

PLLMS[2:0] pins. The User-Select Multiplier Fastboot bootmodes available on the DM6431 are shown

in Table 3-7.

All other modes not shown in these tables are reserved and invalid settings.

For more information on how these pins are sampled at device reset, see Section 6.5.1.2, Latching Boot

and Configuration Pins.

Device Configurations

Submit Documentation Feedback

TMS320DM6431 数据表(PDF) 64 Page - Texas Instruments

TMS320DM6431 数据表(HTML) 64 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表下载