ADE7756 datasheet(14/32 Pages) AD

14 / 32 page

REV. 0

ADE7756

–14–

LINE VOLTAGE SAG DETECTION

In addition to the detection of the loss of the line voltage signal

(zero crossing), the ADE7756 can also be programmed to detect

when the absolute value of the line voltage drops below a certain

peak value, for a number of half-cycles. This condition is illus-

trated in Figure 9.

SAGCYC[7:0] = 06H

6 HALF-CYCLES

SAGLVL[7:0]

FULL SCALE

CHANNEL 2

SAG

SAG RESET HIGH

WHEN CHANNEL 2

EXCEEDS SAGLVL[7:0]

Figure 9. ADE7756 Sag Detection

Figure 9 shows the line voltage fall below a threshold that is set

in the Sag Level register (SAGLVL[7:0]) for nine half-cycles.

Since the Sag Cycle register (SAGCYC[7:0]) contains 06h, the

SAG pin will go active low at the end of the sixth half-cycle for

which the line voltage falls below the threshold, if the DISSAG

bit in the Mode register is Logic 0. As is the case when zero-

crossings are no longer detected, the sag event is also recorded

by setting the SAG flag in the Interrupt Status register. If the

SAG enable bit is set to Logic 1, the

IRQ logic output will go

active low—see ADE7756 Interrupts section.

The

SAG pin will go logic high again when the absolute value

of the signal on Channel 2 exceeds the sag level set in the Sag

Level register. This is shown in Figure 9 when the

SAG pin goes

high during the tenth half-cycle from the time when the signal

on Channel 2 first dropped below the threshold level.

Sag Level Set

The contents of the Sag Level register (1 byte) are compared to

the absolute value of the most significant byte output from

LPF1, after it is shifted left by one bit. Thus for example the

nominal maximum code from LPF1 with a full scale signal on

Channel 2 is 1C396h or (0001, 1100, 0011, 1001, 0110b)—see

Channel 2 Sampling section. Shifting one bit left will give 0011,

1000, 0111, 0010, 1100b or 3872Ch. Therefore writing 38h to

the Sag Level register will put the sag detection level at full

scale. Writing 00h will put the sag detection level at zero. The

Sag Level register is compared to the most significant byte of a

waveform sample after the shift left and detection is made when

the contents of the sag level register are greater.

POWER SUPPLY MONITOR

The ADE7756 also contains an on-chip power supply monitor.

The Analog Supply (AVDD) is continuously monitored by the

ADE7756. If the supply is less than 4 V

± 5%, the ADE7756 will

be inactive, i.e., no energy will accumulate regardless of the

input signals at Channel 1 and Channel 2. This is useful to ensure

correct device operation at power-up and during power-down.

The power supply monitor has built-in hysteresis and filtering.

This gives a high degree of immunity to false triggering due to

noisy supplies.

TIME

AVDD

ADE7756

POWER-ON

RESET

ACTIVE

SAG

INACTIVE

Figure 10. On-Chip Power Supply Monitor

As can be seen from Figure 10, the trigger level is nominally set

at 4 V. The tolerance on this trigger level is about

± 5%. The

SAG pin can also be used as a power supply monitor input to

the MCU. The

SAG pin will go logic low when the ADE7756 is

reset. The power supply and decoupling for the part should

be such that the ripple at AVDD does not exceed 5 V

± 5% as

specified for normal operation.

ADE7756 数据表(PDF) 14 Page - Analog Devices

ADE7756 数据表(HTML) 14 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32

数据表下载