 |
数据搜索系统，热门电子元器件搜索 |
|
|
数据搜索系统，热门电子元器件搜索 |
|
FS32K142BHTXVLLTR 数据表(PDF) 13 Page - NXP Semiconductors |
|
|
|||||||||||||||||||||||||||||
FS32K142BHTXVLLTR 数据表(HTML) 13 Page - NXP Semiconductors |
|
|
13 / 100 page  Table 4. Voltage and current operating requirements for S32K14xW series 1 Symbol Description Min. Max. Unit Notes VDD2 Supply voltage 3.13 5.5 V 3 VDD_OFF Voltage allowed to be developed on VDD pin when it is not powered from any external power supply source. 0 0.1 V VDDA Analog supply voltage 3.13 5.5 V 3 VDD – VDDA VDD-to-VDDA differential voltage – 0.1 0.1 V 3 VREFH ADC reference voltage high 3.13 VDDA + 0.1 V 4 VREFL ADC reference voltage low -0.1 0.1 V VODPU Open drain pullup voltage level VDD VDD V 5 IINJPAD_DC_OP6 Continuous DC input current (positive / negative) that can be injected into an I/O pin -3 +3 mA IINJSUM_DC_OP Continuous total DC input current that can be injected across all I/O pins such that there's no degradation in accuracy of analog modules: ADC and ACMP (See section Analog Modules) — 30 mA 1. Typical conditions assumes VDD = VDDA = VREFH = 5 V, temperature = 25 °C and typical silicon process unless otherwise stated. 2. As VDD varies between the minimum value and the absolute maximum value the analog characteristics of the I/O and the ADC will both change. See section I/O parameters and ADC electrical specifications respectively for details. 3. VDD and VDDA must be shorted to a common source on PCB. The differential voltage between VDD and VDDA is for RF-AC only. Appropriate decoupling capacitors to be used to filter noise on the supplies. See application note AN5032 for reference supply design for SAR ADC. 4. VREFH should always be equal to or less than VDDA + 0.1 V and VDD + 0.1 V 5. Open drain outputs must be pulled to VDD. 6. When input pad voltage levels are close to VDD or VSS, practically no current injection is possible. 4.3 Thermal operating characteristics Table 5. Thermal operating characteristics for S32K1xx series Symbol Parameter Value Unit Min. Typ. Max. TA C-Grade Part Ambient temperature under bias −40 — 851 ℃ TJ C-Grade Part Junction temperature under bias −40 — 1051 ℃ TA V-Grade Part Ambient temperature under bias −40 — 1051 ℃ TJ V-Grade Part Junction temperature under bias −40 — 1251 ℃ TA M-Grade Part Ambient temperature under bias −40 — 1252 ℃ TJ M-Grade Part Junction temperature under bias −40 — 1352 ℃ 1. Values mentioned are measured at ≤ 112 MHz in HSRUN mode. 2. Values mentioned are measured at ≤ 80 MHz in RUN mode. General S32K1xx Data Sheet, Rev. 12, 02/2020 NXP Semiconductors 13 |
|
链接网址 |
| ALLDATASHEET是否为您带来帮助? [ DONATE ] |
关于 Alldatasheet | 广告服务 | 联系我们 | 隐私政策 | 数据表链接 | 链接交换 | 制造商名单 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |
Chinese ▼
English
Chinese
German
Japanese
Russian
Korean
Spanish
French
Italian
Portuguese
Polish
Vietnamese
Indian
Mexican
British
New Zealand
