FS32K142BHTXVLLTR datasheet(11/100 Pages) NXP

11 / 100 page

The supply should be kept in operating conditions and once out of operating conditions, the device should be either reset

or powered off.

Operation with supply between 5.5 V and 5.8 V not in reset condition is allowed for 60 seconds cumulative over lifetime,

the part will operate with reduced functionality.

Operation with supply between 5.5 V and 5.8 V but held in reset condition by external circuit is allowed for 10 hours

cumulative over lifetime.

If the given time limits or supply levels are exceeded, the device may get damaged.

4. When input pad voltage levels are close to VDD or VSS, practically no current injection is possible.

5. While respecting the maximum current injection limit

6. This is the Electronic Control Unit (ECU) supply ramp rate and not directly the MCU ramp rate. Limit applies to both

maximum absolute maximum ramp rate and typical operating conditions.

7. This is the MCU supply ramp rate and the ramp rate assumes that the S32K1xx HW design guidelines in AN5426 are

followed. Limit applies to both maximum absolute maximum ramp rate and typical operating conditions.

8. TJ (Junction temperature)=135 °C. Assumes TA=125 °C for RUN mode

TJ (Junction temperature)=125 °C. Assumes TA=105 °C for HSRUN mode

• Assumes maximum

θJA for 2s2p board. See Thermal characteristics

9. 60 seconds lifetime; device in reset (no outputs enabled/toggling)

Table 2. Absolute maximum ratings for S32K14xW series

Symbol

Parameter

Conditions1

Min

Max

Unit

VDD2

2.7 V - 5. 5V input supply voltage

—

-0.3

5.8 3

VREFH

3.3 V / 5.0 V ADC high reference voltage

—

-0.3

5.8 3

IINJPAD_DC_ABS4

Continuous DC input current (positive /

negative) that can be injected into an I/O

—

-3

VIN_DC

Continuous DC Voltage on any I/O pin

with respect to VSS

—

-0.8

5.85

IINJSUM_DC_ABS

Sum of absolute value of injected currents

on all the pins (Continuous DC limit)

—

Tramp6

ECU supply ramp rate

—

0.5 V/min

500 V/ms

—

Tramp_MCU7

MCU supply ramp rate

—

0.5 V/min

100 V/ms

—

TA8

Ambient temperature

—

-40

150

°C

TSTG

Storage temperature

—

-55

165

°C

VIN_TRANSIENT

Transient overshoot voltage allowed on

I/O pin beyond VIN_DC limit

—

6.8 9

1. All voltages are referred to VSS unless otherwise specified.

2. As VDD varies between the minimum value and the absolute maximum value the analog characteristics of the I/O and the

ADC will both change. See section I/O parameters and ADC electrical specifications respectively for details.

3. 60 seconds lifetime – No restrictions i.e. the part is not held in reset and can switch.

10 hours lifetime – The part is held in reset by an external circuit i.e. the part cannot switch.

The supply should be kept in operating conditions and once out of operating conditions, the device should be either reset

or powered off.

Operation with supply between 5.5 V and 5.8 V not in reset condition is allowed for 60 seconds cumulative over lifetime,

the part will operate with reduced functionality.

Operation with supply between 5.5 V and 5.8 V but held in reset condition by external circuit is allowed for 10 hours

cumulative over lifetime.

If the given time limits or supply levels are exceeded, the device may get damaged.

4. When input pad voltage levels are close to VDD or VSS, practically no current injection is possible.

5. While respecting the maximum current injection limit

General

S32K1xx Data Sheet, Rev. 12, 02/2020

NXP Semiconductors

FS32K142BHTXVLLTR 数据表(PDF) 11 Page - NXP Semiconductors

FS32K142BHTXVLLTR 数据表(HTML) 11 Page - NXP Semiconductors

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100

数据表下载