AD9959SLASHPCBZ datasheet(22/44 Pages) AD

22 / 44 page

AD9959

Data Sheet

Rev. C | Page 22 of 44

In modulation mode, the amplitude frequency phase (AFP)

select bits (CFR[23:22]) and modulation level bits (FR1[9:8])

are programmed to configure the modulation type and level

(see Table 6 and Table 7). Note that the linear sweep enable bit

must be set to Logic 0 in direct modulation mode.

Table 6. Modulation Type Configuration

AFP Select

(CFR[23:22])

Linear Sweep Enable

(CFR[14])

Description

Modulation disabled

Amplitude modulation

Frequency modulation

Phase modulation

Table 7. Modulation Level Selection

Modulation Level (FR1[9:8])

Description

Two-level modulation

Four-level modulation

Eight-level modulation

16-level modulation

When modulating, the RU/RD function can be limited based

on pins available for controlling the feature. The SDIO_x pins

are for RU/RD only, not for modulation.

Table 8. RU/RD Profile Pin Assignments

Ramp-Up/Ramp-Down

(RU/RD) (FR1[11:10])

Description

RU/RD disabled

Only Profile Pin P2 and Profile Pin P3

available for RU/RD operation

Only Profile Pin P3 available for RU/RD

operation

Only SDIO_1, SDIO_2, and SDIO_3

pins available for RU/RD operation;

this forces the serial I/O to be used

only in 1-bit mode

If the profile pins are used for RU/RD, Logic 0 is for ramp-up

and Logic 1 is for ramp-down.

Because of the number of available channels and limited data

pins, it is necessary to assign the profile pins and/or SDIO_1,

SDIO_2, and SDIO_3 pins to a dedicated channel. This is con-

trolled by the profile pin configuration (PPC) bits (FR1[14:12]).

Each of the following modulation descriptions incorporates

data pin assignments.

Two-Level Modulation—No RU/RD

The modulation level bits (FR1[9:8]) are set to 00 (two-level).

The AFP select bits (CFR[23:22]) are set to the desired modulation

type. The RU/RD bits (FR1[11:10]) and the linear sweep enable

bit (CFR[14]) are disabled. Table 9 displays how the profile pins

and channels are assigned.

As shown in Table 9, only Profile Pin P0 can be used to modulate

Channel 0. If frequency modulation is selected and Profile Pin

P0 is Logic 0, Channel Frequency Tuning Word 0 (Register

0x04) is chosen; if Profile Pin P0 is Logic 1, Channel Word 1

(Register 0x0A) is chosen.

Four-Level Modulation—No RU/RD

The modulation level bits are set to 01 (four-level). The AFP

select bits (CFR[23:22]) are set to the desired modulation type.

The RU/RD bits (FR1[11:10]) and the linear sweep enable bit

(CFR[14]) are disabled. Note that the other two channels not

being used should have their AFP select bits set to 00 due to the

lack of profile pins. Table 10 displays how the profile pins and

channels are assigned to each other.

For the conditions in Table 10, the profile (channel word)

Pins [P0:P1] or Profile Pins [P2:P3].

For example, if PPC = 010, [P0:P1] = 11, and [P2:P3] = 01, then

the contents of the Channel Word 3 register of Channel 0 are

presented to the output of Channel 0 and the contents of the

Channel Word 1 register of Channel 3 are presented to the

output of Channel 3.

Table 9. Profile Pin Channel Assignments

Profile Pin Configuration (PPC) (FR1[14:12])

Description

XXX

CH0

CH1

CH2

CH3

Two-level modulation, all channels, no RU/RD

Table 10. Profile Pin and Channel Assignments

Profile Pin Configuration (PPC) (FR1[14:12])

Description

000

CH0

CH1

Four-level modulation on CH0 and CH1, no RU/RD

001

CH0

CH2

Four-level modulation on CH0 and CH2, no RU/RD

010

CH0

CH3

Four-level modulation on CH0 and CH3, no RU/RD

011

CH1

CH2

Four-level modulation on CH1 and CH2, no RU/RD

100

CH1

CH3

Four-level modulation on CH1 and CH3, no RU/RD

101

CH2

CH3

Four-level modulation on CH2 and CH3, no RU/RD

AD9959/PCBZ 数据表(PDF) 22 Page - Analog Devices

AD9959/PCBZ 数据表(HTML) 22 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44

数据表下载

链接网址

AD9959/PCBZ 数据表(PDF) 22 Page - Analog Devices

AD9959/PCBZ 数据表(HTML) 22 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44

数据表 下载

链接网址

数据表下载