| 数据搜索系统,热门电子元器件搜索 |
|
FT800Q-R 数据表(PDF) 7 Page - Bridgetek Pte Ltd. |
|
|
|||||||||||||||||||||||||||||
FT800Q-R 数据表(HTML) 7 Page - Bridgetek Pte Ltd. |
|
7 / 46 page ![]() Copyright © Bridgetek Pte Ltd 7 FT800 Embedded Video Engine Datasheet Version 1.4 Document No.: BRT_000039 Clearance No.: BRT#001 3.2 Pin Description Pin No. Name Type Description 1 AUDIO_L O Audio PWM out, push-pull output, 16mA sink/source current. Pad powered from pin VCC. 2 GND P Ground 3 SPI_SCLK/ I2C_SCL I In SPI mode: SPI SCLK input. In I2C mode: SCL input, need external 1kΩ ~ 4.7kΩ pull up to VCCIO. Input pad with Schmitt trigger, 3.3V tolerant. Pad powered from pin VCCIO. 4 MISO/ I2C_SDA I/O In SPI mode: SPI MISO output. In I2C mode: SDA input/Open Drain Output, need external1kΩ ~ 4.7kΩ pull up to VCCIO. Input with Schmitt trigger, 3.3V tolerant, 4/8/12/16mA sink/source current. Pad powered from pin VCCIO. 5 MOSI/ I2C_SA0 I In SPI mode: SPI MOSI input. In I2C mode: Input, bit 0 of I2C device address. Input pad, 3.3V tolerant. Pad powered from pin VCCIO. 6 CS_N/ I2C_SA1 I In SPI mode: SPI CS_N input, active low. In I2C mode: Input, bit 1 of I2C device address. Input pad, 3.3V tolerant. Pad powered from pin VCCIO. 7 GPIO0/ I2C_SA2 I/O In SPI mode: General purpose input, output port. In I2C mode: Input, bit 2 of I2C device address. Push-pull, three-state output. 3.3V tolerant, 4/8/12/16mA sink/source current. Pad powered from pin VCCIO. 8 GPIO1 I/O General purpose input, output port. Push-pull, three-state output. 3.3V tolerant, 4/8/12/16mA sink/source current. Pad powered from pin VCCIO. 9 VCCIO P I/O power supply, connect a 0.1uF decoupling capacitor. Support 1.8V, 2.5V or 3.3V. Note: VCCIO supply to IO pads from pin 3 to 12 only. 10 MODE I Host interface SPI(pull low) or I2C(pull up) mode select input, 3.3V tolerant Pad powered from pin VCCIO. 11 INT_N OD Host Interrupt, open drain output, active low, pull up to VCCIO through a 1kΩ ~10kΩ resistor. 12 PD_N I Power down input, active low, 3.3V tolerant, pull up to VCCIO through 47kΩ resistor and 100nF to ground. Pad powered from pin VCCIO. 13 X1/ CLK I Crystal oscillator or clock input; Connect to GND if not used. 3.3V peak input allowed. Pad powered from pin VCC. 14 X2 O Crystal oscillator output; leave open if not used. Pad powered from pin VCC. 15 GND P Ground 16 VCC P 3.3V power supply input. 17 VCC1V2 O 1.2V regulator output pin. Connect a 4.7uF decoupling capacitor to GND. 18 VCC P 3.3V power supply input. 19 X+ AI/O Connect to X right electrode of 4-wire touch- screen panel. |
|
链接网址 |
| ALLDATASHEET是否为您带来帮助? [ DONATE ] |
关于 Alldatasheet | 广告服务 | 联系我们 | 隐私政策 | 数据表链接 | 链接交换 | 制造商名单 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |