UPSD325X datasheet(29/176 Pages) STMICROELECTRONICS

29 / 176 page

29/176

µPSD325X DEVICES

Table 14 shows the list of conditional jumps avail-

able to the µPSD325X device user. All of these

jumps specify the destination address by the rela-

tive offset method, and so are limited to a jump dis-

tance of -128 to +127 bytes from the instruction

following the conditional jump instruction. Impor-

tant to note, however, the user specifies to the as-

sembler the actual destination address the same

way as the other jumps: as a label or a 16-bit con-

stant.

There is no Zero Bit in the PSW. The JZ and JNZ

instructions test the Accumulator data for that con-

dition.

The DJNZ instruction (Decrement and Jump if Not

Zero) is for loop control. To execute a loop N

times, load a counter byte with N and terminate the

loop with a DJNZ to the beginning of the loop, as

shown below for N = 10:

MOV COUNTER,#10

LOOP: (begin loop)

•

(end loop)

DJNZ COUNTER, LOOP

(continue)

The CJNE instruction (Compare and Jump if Not

Equal) can also be used for loop control as in Ta-

ble 9. Two bytes are specified in the operand field

of the instruction. The jump is executed only if the

two bytes are not equal. In the example of Table 9

Shifting a BCD Number One Digits to the Right,

the two bytes were data in R1 and the constant

2Ah. The initial data in R1 was 2Eh.

Every time the loop was executed, R1 was decre-

mented, and the looping was to continue until the

R1 data reached 2Ah.

Another application of this instruction is in “greater

than, less than” comparisons. The two bytes in the

operand field are taken as unsigned integers. If the

first is less than the second, then the Carry Bit is

set (1). If the first is greater than or equal to the

second, then the Carry Bit is cleared

Machine Cycles

A machine cycle consists of a sequence of six

states, numbered S1 through S6. Each state time

lasts for two oscillator periods. Thus, a machine

cycle takes 12 oscillator periods or 1µs if the oscil-

lator frequency is 12MHz. Refer to Figure 14, page

30.

Each state is divided into a Phase 1 half and a

Phase 2 half. State Sequence in µPSD325X devic-

es shows that retrieve/execute sequences in

states and phases for various kinds of instructions.

Normally two program retrievals are generated

during each machine cycle, even if the instruction

being executed does

not require it. If the instruc-

tion being executed does not need more code

bytes, the CPU simply ignores the extra retrieval,

and the Program Counter is not incremented.

Execution of a one-cycle instruction (Figure 14,

page 30) begins during State 1 of the machine cy-

cle, when the opcode is latched into the Instruction

the same machine cycle. Execution is complete at

the end of State 6 of this machine cycle.

The MOVX instructions take two machine cycles

to execute. No program retrieval is generated dur-

ing the second cycle of a MOVX instruction. This

is the only time program retrievals are skipped.

The retrieve/execute sequence for MOVX instruc-

tion is shown in Figure 14, page 30 (d).

Table 14. Conditional Jump Instructions

Mnemonic

Operation

Addressing Modes

Dir.

Ind.

Reg.

Imm

JZ rel

Jump if A = 0

Accumulator only

JNZ rel

Jump if A

≠ 0

Accumulator only

DJNZ <byte>,rel

Decrement and jump if not zero

CJNE A,<byte>,rel

Jump if A

≠ <byte>

CJNE <byte>,#data,rel

Jump if <byte>

≠ #data

UPSD325X 数据表(PDF) 29 Page - STMicroelectronics

UPSD325X 数据表(HTML) 29 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表下载