STR910FAM32X6 datasheet(38/78 Pages) STMICROELECTRONICS

38 / 78 page

Pin description

STR91xFA

38/78

4.2

Default pin functions

During and just after reset, all pins on ports 0-9 default to high-impedance input mode until

CPU firmware assigns other functions to the pins. This initial input mode routes all pins on ports

0-9 to be read as GPIO inputs as shown in the “Default Pin Function” column of Table 5.

Simultaneously, certain port pin signals are also routed to other functional inputs as shown in

the “Default Input Function” column of Table 5, and these pin input functions will remain until

CPU firmware makes other assignments. At any time, even after the CPU assigns pins to

alternate functions, the CPU may always read the state of any pin on ports 0-9 as a GPIO input.

CPU firmware may assign alternate functions to port pins as shown in columns “Alternate Input

1” or “Alternate Output 1, 2, 3” of Table 5 by writing to control registers at run-time.

Notes for Table 5:

Notes: 1 STMicroelectronics advises to ground, or pull up to VDDQ using a 100 KΩ resistor, all unused

pins on port 0 - 9 to reduce noise susceptibility, noise generation, and minimize power

consumption. There are no internal or programmable pull-up resistors on ports 0-9.

2 All pins on ports 0 - 9 are 5V tolerant

3 Pins on ports 0,1,2,4,5,7,8,9 have 4 mA drive and 4mA sink. Ports 3 and 6 have 8 mA drive and

8 mA sink.

4 For 8-bit non-muxed EMI operation: Port 8 is eight bits of data, ports 7 and 9 are 16 bits of

address.

5 For 16-bit muxed EMI operation: Ports 8 and 9 are 16 bits of muxed address and data bits, port

7 is up to eight additional bits of high-order address

6 Signal polarity is programmable for interrupt request inputs, EMI_ALE, timer input capture

inputs and output compare/PWM outputs, motor control tach and emergency stop inputs, and

motor control phase outputs.

7 HiZ = High Impedance, V = Voltage Source, G = Ground, I/O = Input/Output

8 STR910FA devices do not support USB. On these devices USBDP and USBDN signals are

"Not Used" (USBDN is not connected, USBDP must be pulled up by a 1.5K ohm resistor to

VDDQ), and all functions named “USB" are not available.

9 STR910FA 128-pin and 144-ball devices do not support Ethernet. On these devices PHYCLK

and all functions named “MII*" are not available.

Table 5.

Device pin description

Pkg

Pin Name

Default Pin

Function

Default Input

Function

Alternate functions

Alternate

Input 1

Alternate

Output 1

Alternate

Output 2

Alternate

Output 3

L11

P0.0

I/O

GPIO_0.0,

GP Input, HiZ

MII_TX_CLK,

PHY Xmit clock

I2C0_CLKIN, I2C

clock in

GPIO_0.0,

GP Output

I2C0_CLKOUT, I2C

clock out

ETM_PCK0, ETM

Packet

69 K10

P0.1

I/O

GPIO_0.1,

GP Input, HiZ

I2C0_DIN,

I2C data in

GPIO_0.1,

GP Output

I2C0_DOUT,

I2C data out

ETM_PCK1, ETM

Packet

J11

P0.2

I/O

GPIO_0.2,

GP Input, HiZ

MII_RXD0,

PHY Rx data0

I2C1_CLKIN, I2C

clock in

GPIO_0.2,

GP Output

I2C1_CLKOUT, I2C

clock out

ETM_PCK2, ETM

Packet

76 H12

P0.3

I/O

GPIO_0.3,

GP Input, HiZ

MII_RXD1,

PHY Rx data

I2C1_DIN,

I2C data in

GPIO_0.3,

GP Output

I2C1_DOUT,

I2C data out

ETM_PCK3, ETM

Packet

78 H10

P0.4

I/O

GPIO_0.4,

GP Input, HiZ

MII_RXD2,

PHY Rx data

TIM0_ICAP1,

Input Capture

GPIO_0.4,

GP Output

EMI_CS0n,

EMI Chip Select

ETM_PSTAT0,

ETM pipe status

STR910FAM32X6 数据表(PDF) 38 Page - STMicroelectronics

STR910FAM32X6 数据表(HTML) 38 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78

数据表下载

链接网址

STR910FAM32X6 数据表(PDF) 38 Page - STMicroelectronics

STR910FAM32X6 数据表(HTML) 38 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78

数据表 下载

链接网址

数据表下载