ICS1893CFILF datasheet(41/126 Pages) ICST

41 / 126 page

Chapter 6 Functional Blocks

ICS1893CF, Rev. F, 03/01/07

Mar. 2007

ICS1893CF Data Sheet Rev. F - Release

Upon receiving a valid STA transaction, during a power-on or hardware reset an ICS1893CF compares the

PHYAD field included within the management frame with the value of its PHYAD bits stored in register 16.

(For information on the PHYAD bits, see Table 7-16.) An ICS1893CF responds to all transactions that

match its stored address bits.

6.6.2.5 Management Frame Register Address

A Management Frame includes a 5-bit register address field, REGAD. This field identifies which of the 32

Management Registers are involved in a transaction between an STA and a PHY.

6.6.2.6 Management Frame Operational Code

A management frame includes a 2-bit operational code field, OP. If the operation code is a:

• Read, the REGAD field identifies the register used as the source of data returned to the STA by the

ICS1893CF.

• Write, the REGAD identifies the destination register that is to receive the data sent by the STA to the

ICS1893CF.

6.6.2.7 Management Frame Turnaround

A valid management frame includes a turn-around field (TA), which is a 2-bit time space between the

REGAD field and the Data field. This time allows an ICS1893CF and an STA to avoid contentions during

read transactions. During an operation that is a:

• Read, an ICS1893CF remains in the high-impedance state during the first bit time and subsequently

drives its MDIO pin to logic zero for the second bit time.

• Write, an ICS1893CF waits while the STA transmits a logic one, followed by a logic zero on its MDIO pin.

6.6.2.8 Management Frame Data

A valid management frame includes a 16-bit Data field for exchanging the register contents between the

ICS1893CF and the STA. All Management Registers are 16 bits wide, matching the width of the Data field.

During a transaction that is a:

• Read, (OP is 10b) the ICS1893CF obtains the contents of the register identified in the REGAD field and

returns this Data to the STA synchronously with its MDC signal.

• Write, (OP is 01b) the ICS1893CF stores the value of the Data field in the register identified in the

REGAD field.

If the STA attempts to:

• Read from a non-existent ICS1893CF register, the ICS1893CF returns logic one for all bits in the Data

field, FFFFh.

• Write to a non-existent ICS1893CF register, the ICS1893CF isolates the Data field of the management

frame from every reaching the registers.

Note: The first Data bit transmitted and received is the most-significant bit of a Management Register, bit

X.15.

6.6.2.9 Serial Management Interface Idle State

The MDIO signal is in an idle state during the time between STA transactions. When the Serial

Management Interface is in the idle state, the ICS1893CF disables (that is, tri-states) its MDIO pin, which

enters a high-impedance state. The ISO/IEC 8802-3 standard requires that an MDIO signal be idle for at

least one bit time between management transactions. However, the ICS1893CF does not have this

limitation and can support a continual bit stream on its MDIO signals.

ICS1893CFILF 数据表(PDF) 41 Page - Integrated Circuit Systems

ICS1893CFILF 数据表(HTML) 41 Page - Integrated Circuit Systems

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表下载