STA381BWS datasheet(43/174 Pages) STMICROELECTRONICS

43 / 174 page

DocID018937 Rev 7

43/174

STA381BWS

I2C bus specification

device address and if a match is found, it acknowledges the identification on SDA bus

during the 9th bit time. The byte following the device identification byte is the internal space

address.

5.3

Write operation

Following the START condition, the master sends a device select code with the RW bit set

to 0. The STA381BWS acknowledges this and then waits for the byte of the internal

address. After receiving the internal byte address the STA381BWS again responds with an

acknowledgement.

5.3.1

Byte write

In the byte write mode the master sends one data byte which is acknowledged by the

STA381BWS. The master then terminates the transfer by generating a STOP condition.

5.3.2

Multi-byte write

The multi-byte write mode can start from any internal address. The master generating a

STOP condition terminates the transfer.

5.4

Read operation

5.4.1

Current address byte read

Following the START condition, the master sends a device select code with the RW bit set

to 1. The STA381BWS acknowledges this and then responds by sending one byte of data.

The master then terminates the transfer by generating a STOP condition.

5.4.2

Current address multi-byte read

The multi-byte read modes can start from any internal address. Sequential data bytes are

read from sequential addresses within the STA381BWS. The master acknowledges each

data byte read and then generates a STOP condition, terminating the transfer.

5.4.3

Random address byte read

Following the START condition, the master sends a device select code with the RW bit set

to 0. The STA381BWS acknowledges this and then the master writes the internal address

byte. After receiving the internal byte address, the STA381BWS again responds with an

acknowledgement. The master then initiates another START condition and sends the device

select code with the RW bit set to 1. The STA381BWS acknowledges this and then

responds by sending one byte of data. The master then terminates the transfer by

generating a STOP condition.

5.4.4

Random address multi-byte read

The multi-byte read mode can start from any internal address. Sequential data bytes are

read from sequential addresses within the STA381BWS. The master acknowledges each

data byte read and then generates a STOP condition, terminating the transfer.

Obsolete

Product(s)

- Obsolete

Product(s)

STA381BWS 数据表(PDF) 43 Page - STMicroelectronics

STA381BWS 数据表(HTML) 43 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表下载

链接网址

STA381BWS 数据表(PDF) 43 Page - STMicroelectronics

STA381BWS 数据表(HTML) 43 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表 下载

链接网址

数据表下载