ST7263B datasheet(59/132 Pages) STMICROELECTRONICS

59 / 132 page

ST7263B

59/132

SERIAL COMMUNICATIONS INTERFACE (Cont’d)

11.3.4.3 Receiver

The SCI can receive data words of either 8 or 9

bits. When the M bit is set, word length is 9 bits

and the MSB is stored in the R8 bit in the SCICR1

Character Reception

During a SCI reception, data shifts in least signifi-

cant bit first through the RDI pin. In this mode, the

SCIDR register consists or a buffer (RDR) be-

tween the internal bus and the received shift regis-

ter (see Figure 35).

Procedure

– Select the M bit to define the word length.

– Select the desired baud rate using the SCIBRR

– Set the RE bit, this enables the receiver which

begins searching for a start bit.

When a character is received:

– The RDRF bit is set. It indicates that the content

of the shift register is transferred to the RDR.

– An interrupt is generated if the RIE bit is set and

the I bit is cleared in the CCR register.

– The error flags can be set if a frame error, noise

or an overrun error has been detected during re-

ception.

Clearing the RDRF bit is performed by the following

software sequence done by:

1. An access to the SCISR register

2. A read to the SCIDR register.

The RDRF bit must be cleared before the end of the

reception of the next character to avoid an overrun

error.

Break Character

When a break character is received, the SPI han-

dles it as a framing error.

Idle Character

When a idle frame is detected, there is the same

procedure as a data received character plus an in-

terrupt if the ILIE bit is set and the I bit is cleared in

the CCR register.

Overrun Error

An overrun error occurs when a character is re-

ceived when RDRF has not been reset. Data can

not be transferred from the shift register to the

RDR register as long as the RDRF bit is not

cleared.

When a overrun error occurs:

– The OR bit is set.

– The RDR content will not be lost.

– The shift register will be overwritten.

– An interrupt is generated if the RIE bit is set and

the I bit is cleared in the CCR register.

The OR bit is reset by an access to the SCISR reg-

ister followed by a SCIDR register read operation.

Noise Error

Oversampling techniques are used for data recov-

ery by discriminating between valid incoming data

and noise.

When noise is detected in a frame:

– The NF is set at the rising edge of the RDRF bit.

– Data is transferred from the Shift register to the

SCIDR register.

– No interrupt is generated. However this bit rises

at the same time as the RDRF bit which itself

generates an interrupt.

The NF bit is reset by a SCISR register read oper-

ation followed by a SCIDR register read operation.

Framing Error

A framing error is detected when:

– The stop bit is not recognized on reception at the

expected time, following either a de-synchroni-

zation or excessive noise.

– A break is received.

When the framing error is detected:

– the FE bit is set by hardware

– Data is transferred from the Shift register to the

SCIDR register.

– No interrupt is generated. However this bit rises

at the same time as the RDRF bit which itself

generates an interrupt.

The FE bit is reset by a SCISR register read oper-

ation followed by a SCIDR register read operation.

ST7263B 数据表(PDF) 59 Page - STMicroelectronics

ST7263B 数据表(HTML) 59 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表下载