STLC5412FN datasheet(41/74 Pages) STMICROELECTRONICS

41 / 74 page

in a known deactivated state, e.g. in an LT after a

DI status indication has been reported. In GCI, C/I

indication DI is sent twice on Br output before UID

powers down.

0110 (UAR): U-interface-only Activation Request

Being in Power Up and deactivated , UAR com-

mand forces UID through the appropriate se-

quence to activate the loop without activating the

S/T interface. SL2/SL3 signal is sent with uoa bit

set to zero. With the line already active, UAR

command forces bit uoa equal zero: this is in-

tended to deactivate the S/T interface.

0111 (QM): Quiet Mode

This command has the same effect as in NT

mode.

1000 (AR): Activation Request

Being Power Up and deactivated, AR instruction

forces UID through the appropriate sequence to

activate the line by sending TL followed by SL1.

SL2/SL3 signal is sent with uoa bit equal one.

Beeing in the U-only-active states, AR command

forces the uoa bit equal 1 to the line. AR is in-

tended to activate the S/T interface.

1010 (ARL): Activation Request with Loopback

ARL test command forces UID through the appro-

priate sequence to activate with the complete

transmit data stream looped-back to the receiver.

When this loop-back is disabled by DR command,

UID is ready to operate a warm start if a new ARL

command is issued.

1011 (SP3): Send Single Pulse +3, -3

SP3 test command forces UID to

send +3, -3

pulses to the line, one pulse per frame.

1100 (AI): Activation Indicate

AI is an optional command recognized only when

BP2 bit in CR2 register is set equal one or LT-

RR-AUTO mode is selected. Being in the super-

frame-synchronized state with act bit received

from the line equal one, AI command allows UID

to send act bit equal one to the line.

1111 (DI): Deactivation Indicate

The DI command allows the UID to automatically

enter the power down state if the line is deacti-

vated. DI command has no effect as long as the

line is not deactivated (DI status indication re-

ported).

LT mode: Status indication

0001 (EIU): Error Indication Interface U

It can be a ”loss of signal”, a ”loss of sync.” or an

expiry of 15s timer. EIU is also the answer to the

RES comand.

After sending EIU, the UID is always ready for a

cold start.

0100 (EI): Error Indication

EI status indication reports that act bit has been

detected equal zero.

0110 (UAI): U interface Activation Indication

UAI reports that the line is superframe synchro-

nized.

1000 (AP): Activation Pending

Being in one of the deactivated states, AP reports

that a wake up tone has been detected from the

line. Beeing in the U-only-activated state, AP re-

ports that sai bit has been detected equal one

from the line. It is intended to reflect an activation

attempt at the S/T interface.

1100 (AI): Activation Indication

AI reports that UID is superframe synchronized

with act bit received equal one. TE side of the

loop relative to the UID is active

1111 (DI): Deactivation Indication

DI reports that UID has entered the deactivated

state (J1).

B1, B2 AND D CHANNELS TRANSPARENCY

UID is able to control automatically transparency of

B1, B2 and D channels. Nevertheless, when ETC

bit in CR2 register is set equal 1, transparency is

forced as soon as the line is synchronized.

It is also possible to control each data channel B1,

B2, D enabling at the DSI/GCI interface inde-

pendently by means of bits EB1, EB2 and ED in

CR4 register. Set to 1, B1, B2 or D channel on the

DSI/GCI interface are enabled. In this case, out of

the transparency state (s), ones are forced on the

relevant time slot of the DSI/GCI, and ones or zeros

are transmitted on the line conforming recommen-

dations. Set equal 0, relevant time slot on DSI/GCI

is always in high impedance state and ones or ze-

ros are transmitted on the line. In this last case, as

soon as transparency is enabled, ones are trans-

mitted to the line.

When RDT test command is applied, transpar-

ency on 2B+D is forced. This intend to permit the

user, if required, to send a random sequence of

bits to the line. Please note that the on-chip

scrambler normally ensures

transmission of

equiprobable levels to the line, even if logical one

only is provided to the DSI/GCI system interface.

INTERNAL REGISTERS DESCRIPTION.

Here

following

detailed

description

STLC5412 internal registers.

Internal registers can be accessed:

a) In GCI mode, according to the Monitor channel

exchange rules. For RXACT and TXACT also

through C/I channel.

b) in

µW/DSI mode, using the MICROWIRE inter-

face according to the rules described in section

”

µW control interface”.

Tables 8 and 10 gives the list of all STLC5412 in-

ternal registers.

Registers are grouped by types and address ar-

eas:

STLC5412

41/74

STLC5412FN 数据表(PDF) 41 Page - STMicroelectronics

STLC5412FN 数据表(HTML) 41 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74

数据表下载