STLC5466 datasheet(61/130 Pages) STMICROELECTRONICS

61 / 130 page

61/130

STLC5466

VI.34 - Split Fetch Memory Register

SFMR (4E)H

This register must be programmed after reset before the first SDRAM access. Writing register is forbidden

between two SDRAM accesses.

SWAP

SWAP=1

The first byte (named 2b) of frames received (or transmitted) by the HDLCs is stored in bit 8/15

of the shared memory (or located in bit 8/15); the first bit received is stored in bit 8 of the shared

memory.

The first bit to be transmitted is located in bit 8 of the shared memory.

The second byte (named 2b+1) of the frame received (or transmitted) by the HDLCs is stored in

bit 0/7 of the shared memory; the first bit of the second byte received is stored in bit 0 of the

shared memory.

The ninth bit to be transmitted is located in bit 0 of the shared memory.

The bytes named (2b) are located in bit 8/15 of the shared memory; b from 0 to 2047.

The bytes named (2b+1) are located in bit 0/7of the shared memory.

SWAP=0

The first byte (named 2b) of frames received (or transmitted) by the HDLCs is stored in bit 0/7

of the shared memory (or located in bit 0/7); the first bit received is stored in bit 0 of the shared

memory.

The first bit to be transmitted is located in bit 0 of the shared memory.

The second byte (named 2b+1) of the frame received (or transmitted) by the HDLCs is stored in

bit 8/15 of the shared memory; the first bit of the second received is stored in bit 8 of the shared

memory.

The ninth bit to be transmitted is located in bit 8 of the shared memory.

The bytes named (2b) are located in bit 0/7 of the shared memory; b from 0 to 2047

The bytes named (2b+1) are located in bit 8/15 of the shared memory.

bit15

bit8

bit7

bit0

A23

A22

A21

A20

A19

A18

A17

A16

NAB

FFA

After reset (0000)H

FFA

: Fast Fetch memory Access. This bit is taken into account only when synchronous 386EX micro-

processor is selected.

FFA = 1; in case of read from synchronous 386EX microprocessor

• if LBA delivered by the microprocessor is at”1”,

• if the word is already in the Fetch memory,

• if the Write FIFO is empty,

• if no current burst due to a previous read Access

then there is no Twait.

FFA = 0; in case of read from synchronous 386EX microprocessor with the same conditions de-

scribed above there is one Twait.

NAB

: No Anticipation Burst

NAB = 1.

A read burst is generated only when a word required by the microprocessor is not present in the

fetch memory. No anticipation is done for potential further accesses.

NAB = 0.

An anticipation is added to the fetch memory management.

If one of four words of a burst is read by the microprocessor in the fetch memory and

if the following four words are not present and valid in the fetch memory,

then the following four words are transferred automatically by anticipation from SDRAM to the

fetch memory.

STLC5466 数据表(PDF) 61 Page - STMicroelectronics

STLC5466 数据表(HTML) 61 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表下载

链接网址

STLC5466 数据表(PDF) 61 Page - STMicroelectronics

STLC5466 数据表(HTML) 61 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表 下载

链接网址

数据表下载