ATtiny10 datasheet(79/168 Pages) ATMEL

79 / 168 page

8127C–AVR–10/09

ATtiny4/5/9/10

11.11.9

TIFR0 – Timer/Counter Interrupt Flag Register 0

• Bits 7:6, 4:3 – Reserved Bits

These bits are reserved for future use. For ensuring compatibility with future devices, these bits

must be written to zero when the register is written.

• Bit 5 – ICF0: Timer/Counter0, Input Capture Flag

This flag is set when a capture event occurs on the ICP0 pin. When the Input Capture Register

(ICR0) is set by the WGM03:0 to be used as the TOP value, the ICF0 flag is set when the coun-

ter reaches the TOP value.

ICF0 is automatically cleared when the Input Capture Interrupt Vector is executed. Alternatively,

ICF0 can be cleared by writing a logic one to its bit location.

• Bit 2 – OCF1B: Timer/Counter0, Output Compare B Match Flag

This flag is set in the timer clock cycle after the counter (TCNT0) value matches the Output

Compare Register B (OCR0B).

Note that a Forced Output Compare (0B) strobe will not set the OCF0B flag.

OCF1B is automatically cleared when the Output Compare Match B Interrupt Vector is exe-

cuted. Alternatively, OCF1B can be cleared by writing a logic one to its bit location.

• Bit 1 – OCF0A: Timer/Counter0, Output Compare A Match Flag

This flag is set in the timer clock cycle after the counter (TCNT0) value matches the Output

Compare Register A (OCR0A).

Note that a Forced Output Compare (1A) strobe will not set the OCF0A flag.

OCF0A is automatically cleared when the Output Compare Match A Interrupt Vector is exe-

cuted. Alternatively, OCF0A can be cleared by writing a logic one to its bit location.

• Bit 0 – TOV0: Timer/Counter0, Overflow Flag

The setting of this flag is dependent of the WGM03:0 bits setting. In Normal and CTC modes,

the TOV0 flag is set when the timer overflows. See Table 11-5 on page 75 for the TOV0 flag

behavior when using another WGM03:0 bit setting.

TOV0 is automatically cleared when the Timer/Counter0 Overflow Interrupt Vector is executed.

Alternatively, TOV0 can be cleared by writing a logic one to its bit location.

11.11.10 GTCCR – General Timer/Counter Control Register

• Bit 7 – TSM: Timer/Counter Synchronization Mode

Writing the TSM bit to one activates the Timer/Counter Synchronization mode. In this mode, the

value that is written to the PSR bit is kept, hence keeping the Prescaler Reset signal asserted.

Bit

7654

0x2A

–

–ICF0

–

OCF0B

OCF0A

TOV0

TIFR0

Read/Write

R/W

Initial Value

0000

Bit

0x2F

TSM

–

PSR

GTCCR

Read/Write

R/W

Initial Value

ATtiny10 数据表(PDF) 79 Page - ATMEL Corporation

ATtiny10 数据表(HTML) 79 Page - ATMEL Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表下载