TNETX3110 datasheet(27/65 Pages) TI1

27 / 65 page

TNETX3110

ThunderSWITCH

™ 8/3 ETHERNET™ SWITCH

WITH 8 10-MBIT/S PORTS AND 3 10-/100-MBIT/S PORTS

SPWS047A – MARCH 1998 – REVISED APRIL 1999

POST OFFICE BOX 655303

• DALLAS, TEXAS 75265

EEPROM interface (continued)

Multiple bus masters are not supported on the EEPROM interface because the ECLK pin always is driven by

the device with a strong 0/strong 1 (i.e., not a strong 1/resistively pulled-up 1).

An Ethernet CRC check is used to ensure the EEPROM data is valid. The 4-byte CRC should be placed within

the EEPROM in four data bytes immediately following the last byte to be loaded (equivalent to locations

0x00FC–0x00FF, just above Syscontrol). As each byte is loaded from the EEPROM, the bits within that byte

are entered into the CRC checker bit-wise, most significant bit first.

A valid CRC always must be provided by the EEPROM. The EEPROM data for the most significant bit of

Syscontrol is withheld until the CRC computed by the device has been checked against the one read from the

EEPROM. If the CRC is invalid:

D The reset bit is set to 1 in Syscontrol, load and initd are both 0, and the TNETX3110 does not begin

operation.

D The fault LED is illuminated and remains in that state until the TNETX3110 is hardware reset or until load

in Syscontrol is set to 1.

interaction of EEPROM load with the SIO register

The EDIO pin is shared with the SIO register edata bit. The edata and etxen bits must not both be set to 1 when

the load bit is set or the EDIO pin is held at resistive 1 and the EEPROM load fails.

The value of the eclk bit in SIO is don’t care when load is set, but to ensure the EEPROM does not see a glitch

on its clock signal, the load bit should not be set until the minimum clock high or low time required by the

EEPROM on its clock signal has expired since the eclk bit was last changed.

The SIO register is not loaded during the EEPROM download.

summary of EEPROM load outcomes

Table 6 summarizes the various states of register bits and the fault LED for each possible outcome, following

an EEPROM load attempt.

Table 6. Summary of EEPROM Load Outcomes

OUTCOME

STOP

LOAD

INITD†

FAULT LED

ECLK

Successful load

0‡

Not locked

No EEPROM present

0‡

Locked

CRC error detected

Not locked

† Assuming the start bit was set to 1 by the EEPROM load

‡ Assuming the fault bit in LEDControl = 0 and no memory system parity error is detected

compatibility with future device revisions

All EEPROM locations that correspond to reserved addresses in the memory map, register bits that are read

only, and register bits that are marked as reserved should be set to 0 to ensure compatibility with future versions

of the device. Failure to do so may result in the unintentional activation of features in future devices. All such

bits are included in the CRC calculation.

TNETX3110 数据表(PDF) 27 Page - Texas Instruments

TNETX3110 数据表(HTML) 27 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65

数据表下载