APFCON datasheet(174/222 Pages) MICROCHIP

174 / 222 page

MCP19111

DS22331A-page 174

 2013 Microchip Technology Inc.

27.5.8

ACKNOWLEDGE SEQUENCE

TIMING

An Acknowledge sequence is enabled by setting the

Acknowledge Sequence Enable bit, ACKEN bit of the

SSPCON2 register. When this bit is set, the SCL pin is

pulled low and the contents of the Acknowledge data bit

are presented on the SDA pin. If the user wishes to gen-

erate an Acknowledge, then the ACKDT bit should be

cleared. If not, the user should set the ACKDT bit before

starting an Acknowledge sequence. The Baud Rate

Generator then counts for one rollover period (TBRG)

and the SCL pin is deasserted (pulled high). When the

SCL pin is sampled high (clock arbitration), the Baud

Rate Generator counts for TBRG. The SCL pin is then

pulled low. Following this, the ACKEN bit is automatically

cleared, the Baud Rate Generator is turned off and the

MSSP module then goes into Idle mode (Figure 27-22).

27.5.8.1

WCOL Status Flag

If the user writes the SSPBUF when an Acknowledge

sequence is in progress, then WCOL is set and the

contents of the buffer are unchanged (the write does

not occur).

27.5.9

STOP CONDITION TIMING

A Stop bit is asserted on the SDA pin at the end of a

receive/transmit by setting the Stop Sequence Enable

bit, PEN bit of the SSPCON2 register. At the end of a

receive/transmit, the SCL line is held low after the

falling edge of the 9th clock. When the PEN bit is set,

the master will assert the SDA line low. When the SDA

line is sampled low, the Baud Rate Generator is

reloaded and counts down to ‘0’. When the Baud Rate

Generator times out, the SCL pin will be brought high

and one TBRG (Baud Rate Generator rollover count)

later, the SDA pin will be deasserted. When the SDA

pin is sampled high while SCL is high, the P bit of the

SSPSTAT register is set. A TBRG later, the PEN bit is

cleared and the SSPIF bit is set (Figure 27-23).

27.5.9.1

WCOL Status Flag

If the user writes the SSPBUF when a Stop sequence

is in progress, then the WCOL bit is set and the

contents of the buffer are unchanged (the write does

not occur).

FIGURE 27-22:

ACKNOWLEDGE SEQUENCE WAVEFORM

FIGURE 27-23:

STOP CONDITION RECEIVE OR TRANSMIT MODE

SDA

SCL

SSPIF set at

Acknowledge sequence starts here,

write to SSPCON2

ACKEN automatically cleared

Cleared in

TBRG

the end of receive

ACKEN = 1, ACKDT = 0

SSPIF

software

SSPIF set at the end

of Acknowledge sequence

Cleared in

software

ACK

Note:

TBRG = one Baud Rate Generator period.

SCL

SDA

SDA asserted low before rising edge of clock

Write to SSPCON2,

set PEN

Falling edge of

SCL = 1 for TBRG, followed by SDA = 1 for TBRG

9th clock

SCL brought high after TBRG

TBRG

after SDA sampled high. P bit (SSPSTAT<4>) is set.

TBRG

to setup Stop condition

ACK

TBRG

PEN bit (SSPCON2<2>) is cleared by

hardware and the SSPIF bit is set

Note:

TBRG = one Baud Rate Generator period.

APFCON 数据表(PDF) 174 Page - Microchip Technology

APFCON 数据表(HTML) 174 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表下载

链接网址

APFCON 数据表(PDF) 174 Page - Microchip Technology

APFCON 数据表(HTML) 174 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表 下载

链接网址

数据表下载