K3HB-R datasheet(29/32 Pages) OMRON

29 / 32 page

Digital Indicators

K3HB-R/-P/-C

Outputs

Standard, zone, and level comparative output patterns can be

selected for comparative outputs.

Prevents comparative outputs from chattering when the

measurement value fluctuates slightly near the set value.

Holds the output status when a comparative result output other than

PASS turns ON.

Comparative results other than PASS and error signals can be

output from the PASS output terminal.

Delays turning OFF comparatives for a set period. This can be used

to provide sufficient time to read the comparative output ON status

when the comparative result changes at short intervals.

Turns ON the comparative output for a specific time.

Reverses the output logic of comparative results.

Measurements can be stopped for a set time using an external input.

Output operation can be checked without using actual input signals

by using the keys to set a test measurement value.

A current or voltage proportional to the change in the measurement

value can be output.

The comparison outputs can be kept OFF until the measurement

value enters the PASS range.

Display

The display value can be set to the present value, the maximum

value, or the minimum value.

The present value display color can be set to green or red. The color

of the present value can also be switched according to the

comparative output.

When the input changes rapidly, the display refresh period can be

lengthened to control flickering and make the display easier to read.

The present measurement value can be displayed as a position in

relation to the scaling width on a 20-gradation position meter.

The input signal can be converted and displayed as any value.

Select whether or not to display the comparative value during

operation.

Automatically returns the display to RUN level when there are no key

operations (e.g., max./min. switching, bank settings using keys).

Other

Holds the maximum and minimum measurement values.

Switch between 8 comparative value banks using the keys on the

front panel or external inputs. A set of set comparative values can be

selected as a group.

Any bank settings can be copied to all banks.

The measured value can be recorded when the power supply is

interrupted.

The K3HB can be calibrated by the user.

Comparative Output Pattern

out-p

Hysteresis

hys

Output Refresh Stop

o-stp

PASS Output Change

pass

Output OFF Delay

off-d

Shot Output

shot

Output Logic

out-n

Startup Compensation Timer

s-tmr

Output Test

test

Linear Outputs

lset.c, lset.v, lset.h, lset.l

Standby Sequence

stdby

R P C

R P

R P C

R P

Display Value Selection

disp

Display Color Selection

color

Display Refresh Period

d.ref

Position Meter

pos-t, pos-h, pos-l

Prescale

ps.ax, ps.ay, ps.bx, ps.by

Comparative Set Value Display

sv.dsp

Display auto-return

ret

Max./Min. Hold

Bank Selection

bnk-c

Bank Copy

copy

Interruption Memory

memo

User Calibration

R P C

R P

R P C

K3HB-R 数据表(PDF) 29 Page - Omron Electronics LLC

K3HB-R 数据表(HTML) 29 Page - Omron Electronics LLC

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32

数据表下载

链接网址

K3HB-R 数据表(PDF) 29 Page - Omron Electronics LLC

K3HB-R 数据表(HTML) 29 Page - Omron Electronics LLC

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32

数据表 下载

链接网址

数据表下载