6

Rotary Pulse Indicator

K3HB-R

■ Characteristics

Display range

−19,999 to 99,999

Measurement accuracy

(at 23±5

°C)

Functions F1, F6: ±0.006% rgd ±1 digit (for voltage pulse/open collector sensors)

Functions F2 to F5: ±0.02% rgd ±1 digit (for voltage pulse/open collector sensors)

Measurement range

Functions F1 to F6: 0.5 mHz to 50 kHz (for voltage pulse/open collector sensors)

Input signals

No-voltage contact (30-Hz max. with ON/OFF pulse width of 15 ms min.)

Voltage pulse (50-KHz max. with ON/OFF pulse width of 9 µs min.; ON voltage: 4.5 to 30 V;

OFF voltage:

−30 to 2 V; input impedance: 10 kΩ)

Open collector (50-KHz max. with ON/OFF pulse width of 9 µs min.)

Connectable sensors

ON residual voltage: 3 V max.

OFF leakage current: 1.5 mA max.

Load current:

Must have a switching capacity of 20 mA or higher.

Must be able to properly switch load currents of 5 mA or less.

Comparative output response

time (transistor output)

Functions F1 to F6: 100 ms max. (time until the comparative output is made when there is a forced sudden

change in the input signal from 15% to 95% or 95% to 15%.)

Linear output response time

Functions F1 to F6: 110 ms max. (time until the final analog output value is reached when there is a forced

sudden change in the input signal from 15% to 95% or 95% to 15%.)

Insulation resistance

20 M

Ω min. (at 500 VDC)

Dielectric strength

2,300 VAC for 1 min between external terminals and case

Noise immunity

100 to 240 VAC models:

±1,500 V at power supply terminals in normal or common mode

(waveform with 1-ns rising edge and pulse width of 1

µs/100 ns)

24 VAC/VDC models:

±1,500 V at power supply terminals in normal or common mode

(waveform with 1-ns rising edge and pulse width of 1

µs/100 ns)

Vibration resistance

Shock resistance

Weight

Approx. 300 g (Base Unit only)

Degree of

protection

Front panel

Conforms to NEMA 4X for indoor use (equivalent to IP66)

Rear case

IP20

Terminals

IP00 + finger protection (VDE0106/100)

Memory protection

EEPROM (non-volatile memory)

Number of rewrites: 100,000

Applicable standards

UL61010C-1, CSA C22.2 No. 1010.1 (evaluated by UL)

EN61010-1 (IEC61010-1): Pollution degree 2/Overvoltage category II

EN61326: 1997, A1: 1998, A2: 2001

EMC

EMI: EN61326+A1 industrial applications

Electromagnetic radiation interference

CISPR 11 Group 1, Class A: CISPRL16-1/-2

Terminal interference voltage

CISPR 11 Group 1, Class A: CISPRL16-1/-2

EMS: EN61326+A1 industrial applications

Electrostatic Discharge Immunity

EN61000-4-2: 4 kV (contact), 8 kV (in air)

Radiated Electromagnetic Field Immunity

EN61000-4-3: 10 V/m 1 kHz sine wave amplitude modulation (80 MHz to 1 GHz, 1.4 to 2 GHz)

Electrical Fast Transient/Burst Immunity

EN61000-4-4: 2 kV (power line), 1 kV (I/O signal line)

Surge Immunity

EN61000-4-5: 1 kV with line (power line), 2 kV with ground (power line)

Conducted Disturbance Immunity

EN61000-4-6: 3 V (0.15 to 80 MHz)

Power Frequency Magnetic Immunity

EN61000-4-8: 30 A/m (50 Hz) continuous time

Voltage Dips and Interruptions Immunity

EN61000-4-11: 0.5 cycle, 0

°/180°, 100% (rated voltage)