AD6620SSLASHPCB datasheet(32/44 Pages) AD

32 / 44 page

AD6620

–32–

REV. A

Read Pseudocode

int read_micro(ext_address);

main();

{

* This code shows the reading of the NCO frequency register

using the read_micro function as defined above. The variable

address is the External Address A[2..0] and data is the value to

be placed in the external interface register. The NCO register is

located at Internal Address = 0x303.

// holding registers for NCO byte wide access data

int d3, d2, d1, d0;

// NCO frequency word (32-bits wide)

// write AMR

write_micro(7, 0x03 );

// write LAR

write_micro(6, 0x03);

* read D[7:0] from DR0, All data is moved from the Internal

Registers to the interface registers on this access. Reading

should be initiated with a read from DR0. Therefore, DR1,

DR2 and DR3 can be read after DR0

d0 = read_micro(0) & 0xFF;

// read D[15:8] from DR1

d1 = read_micro(1) & 0xFF;

// read D[23:16] from DR2

d2 = read_micro(2) & 0xFF;

// read D[31:24] from DR3

d3 = read_micro(3) & 0xFF;

// DR4 is not needed because NCO_FREQ is only 32-bits

// Assemble 32-bit NCO_FREQ word from the 4 byte

components

NCO_FREQ = d0 + (d1 << 8) + (d2 << 16) + (d3 << 24);

} // end of main

Auto Increment Feature

To increase throughput, an auto increment feature is provided.

This feature is controlled by Bits 6 and 7 of the AMR. If these

bits are set to 00, the address remains the same after an internal

access. If set to 01, the address is incremented after a read access

has been performed. If set to 10, the address is incremented

after a write access is performed. If set to 11, the address is incre-

mented after each access, read or write. This allows the AD6620

to be initialized in a much shorter time since the access to the

LAR and AMR must occur only once to initialize or read-back

the entire device.

MICROPORT CONTROL

External reads and writes are accomplished in one of two modes

via the Microprocessor Port. The

CS, RD (DS), RDY (DTACK),

WR (R/W) and MODE pins are used to control the access. The

specific function of these pins depends on whether the access is

MODE 0 or MODE 1. The Mode 1 signal names are those

listed on the pinout. The access mode is controlled by the

MODE input as described in the following sections.

Table XII. Microprocessor Control Signals

MODE 0

MODE 1

A[2:0] (Address Lines)

D[7:0] (Data Lines)

CS (Chip Select)

RD (Read Strobe)

DS (Data Strobe)

WR (Write Strobe)

R/W (Read/Write Select)

RDY (Ready Signal)

DTACK (Data Acknowledge)

MODE (Mode Select)

The Microport is synchronous with the master clock (CLK) of

the AD6620, but the interface is not required to be. If the speed

of the interface is significantly slower than CLK, synchronicity

should not be an issue. If the interface is relatively fast com-

pared to CLK, the user may need to synchronize the Microport

to CLK or add wait states to the controlling processor. The

timing diagrams show the relationship of the control signals to

clock and the user should use these as a guide to implement a

Microport interface.

AD6620S/PCB 数据表(PDF) 32 Page - Analog Devices

AD6620S/PCB 数据表(HTML) 32 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44

数据表下载