| 数据搜索系统,热门电子元器件搜索 |
|
AD6620S/PCB 数据表(PDF) 23 Page - Analog Devices |
|
|
|||||||||||||||||||||||||||||
AD6620S/PCB 数据表(HTML) 23 Page - Analog Devices |
|
23 / 44 page ![]() AD6620 –23– REV. A The frequency response of the filter is given by the following equations. The gain and pass band droop of CIC5 should be calculated by these equations. Both parameters may be compen- sated for in the RCF stage. Hz z z S M CIC CIC () – – – – =× + 1 2 1 1 5 5 51 5 Hf Mf f f f S CIC SAMP SAMP CIC () sin sin =× × + 1 2 5 5 5 2 2 5 π π The scale factor, SCIC5 is a programmable unsigned integer between 0 and 20. It serves to control the attenuation of the data into the CIC5 stage in 6 dB increments. For the best dynamic range, SCIC5 should be set to the smallest value possible (lowest attenuation) without creating an overflow condition. This can be safely accomplished using the equation below, where OLCIC2 is the largest fraction of full scale possible at the input to this filter stage. This value is output from the CIC2 stage then pipe- lined into the CIC5. SCIC5 is ignored when this filter is bypassed by setting MCIC5 = 1. S ceil M OL OL M OL CIC CIC CIC CIC CIC S CIC CIC 52 5 5 2 5 5 5 5 2 5 2 5 =× () = () × + log ( ) – when CIC5 is bypassed; OL OL CIC CIC 52 = The output rate of this stage is given by the equation below. f f M SAMP SAMP CIC 5 2 5 ≤ –0.5 –120 –100 –80 –60 –40 –20 0 f/fSAMP –0.4 –0.3 –0.2 –0.1 0.1 0.2 0.3 0.4 0.5 0 –0.5 –120 –100 –80 –60 –40 –20 0 f/fSAMP2 –0.4 –0.3 –0.2 –0.1 0.1 0.2 0.3 0.4 0.5 0 Figure 37. CIC2 Alias Rejection, MCIC2 = 16 5TH ORDER CASCADED INTEGRATOR COMB FILTER The third signal processing stage, CIC5, implements a sharper fixed-coefficient, decimating filter than CIC2. The input rate to this filter is fSAMP2. The maximum input rate is given by the equation below. NCH equals two for Diversity Channel Real input mode; otherwise NCH equals one. In order to satisfy this equation, MCIC2 can be increased, NCH can be reduced, or fCLK can be increased (reference fractional rate input timing described in the Input Timing section). f f N SAMP CLK CH 2 2 ≤ × The decimation ratio, MCIC5, may be programmed from 1 to 32 (all integer values). When MCIC5 = 1, this stage is bypassed and the CIC5 scale factor is ignored. |
|
链接网址 |
| ALLDATASHEET是否为您带来帮助? [ DONATE ] |
关于 Alldatasheet | 广告服务 | 联系我们 | 隐私政策 | 数据表链接 | 链接交换 | 制造商名单 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |