LTC2410IGN datasheet(23/44 Pages) LINER

23 / 44 page

LTC2410

APPLICATIO S I FOR ATIO

In addition to the input sampling charge, the input ESD

protection diodes have a temperature dependent leakage

current. This current, nominally 1nA (

±10nA max), results

in a small offset shift. A 100

Ωsource resistance will create

a 0.1

µV typical and 1µV maximum offset voltage.

Reference Current

In a similar fashion, the LTC2410 samples the differential

reference pins REF+ and REF– transfering small amount of

charge to and from the external driving circuits thus

producing a dynamic reference current. This current does

not change the converter offset but it may degrade the gain

and INL performance. The effect of this current can be

analyzed in the same two distinct situations.

For relatively small values of the external reference capaci-

tors (CREF < 0.01µF), the voltage on the sampling capacitor

settles almost completely and relatively large values for

the source impedance result in only small errors. Such

values for CREF will deteriorate the converter offset and

gain performance without significant benefits of reference

filtering and the user is advised to avoid them.

Larger values of reference capacitors (CREF > 0.01µF) may

be required as reference filters in certain configurations.

Such capacitors will average the reference sampling charge

and the external source resistance will see a quasi con-

stant reference differential impedance. When FO = LOW

(internal oscillator and 60Hz notch), the typical differential

reference resistance is 1.3M

Ω which will generate a gain

error of approximately 0.38ppm for each ohm of source

resistance driving REF+ or REF–. When FO = HIGH (internal

oscillator and 50Hz notch), the typical differential refer-

ence resistance is 1.56M

Ωwhichwillgenerateagainerror

of approximately 0.32ppm for each ohm of source resis-

tance driving REF+ or REF–. When FO is driven by an

external oscillator with a frequency fEOSC (external conver-

sion clock operation), the typical differential reference

resistance is 0.20 • 1012/fEOSCΩ and each ohm of source

resistance drving REF+ or REF– will result in

2.47 • 10–6 • fEOSCppm gain error. The effect of the source

resistance on the two reference pins is additive with

respect to this gain error. The typical +FS and –FS errors

for various combinations of source resistance seen by the

Figure 19. +FS Error vs RSOURCE at IN

+ or IN– (Large CIN)

Figure 20. –FS Error vs RSOURCE at IN+ or IN– (Large CIN)

Figure 21. Offset Error vs Common Mode Voltage

(VINCM = IN+ = IN–) and Input Source Resistance Imbalance

(

∆RIN = RSOURCEIN+ – RSOURCEIN–) for Large CIN Values (CIN ≥ 1µF)

RSOURCE (Ω)

0 100 200 300 400 500 600 700 800 900 1000

2410 F19

300

240

180

120

VCC = 5V

REF+ = 5V

REF – = GND

IN+ = 3.75V

IN– = 1.25V

FO = GND

TA = 25°C

CIN = 0.01µF

CIN = 0.1µF

CIN = 1µF, 10µF

RSOURCE (Ω)

0 100 200 300 400 500 600 700 800 900 1000

2410 F20

–60

–120

–180

–240

–300

VCC = 5V

REF+ = 5V

REF – = GND

IN+ = 1.25V

IN– = 3.75V

FO = GND

TA = 25°C

CIN = 0.01µF

CIN = 0.1µF

CIN = 1µF, 10µF

VINCM (V)

0.5

1.5

2.5

3.5

4.5

2410 F21

120

100

–20

–40

–60

–80

–100

–120

FO = GND

TA = 25°C

RSOURCEIN– = 500Ω

CIN = 10µF

VCC = 5V

REF+ = 5V

REF – = GND

IN+ = IN– = VINCM

∆RIN = +400Ω

∆RIN = +200Ω

∆RIN = +100Ω

∆RIN = 0Ω

∆RIN = –100Ω

∆RIN = –200Ω

∆RIN = –400Ω

LTC2410IGN 数据表(PDF) 23 Page - Linear Technology

LTC2410IGN 数据表(HTML) 23 Page - Linear Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44

数据表下载

链接网址

LTC2410IGN 数据表(PDF) 23 Page - Linear Technology

LTC2410IGN 数据表(HTML) 23 Page - Linear Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44

数据表 下载

链接网址

数据表下载