PIC16LC773 datasheet(55/200 Pages) MICROCHIP

55 / 200 page

PIC16C77X

Advance Information

DS30275A-page 55

FIGURE 8-2:

SSPCON: SYNC SERIAL PORT CONTROL REGISTER (ADDRESS 14h)

R/W-0

WCOL

SSPOV

SSPEN

CKP

SSPM3

SSPM2

SSPM1

SSPM0

R = Readable bit

W = Writable bit

- n = Value at POR reset

bit7

bit0

bit 7:

WCOL: Write Collision Detect bit

Master Mode:

1 = A write to the SSPBUF register was attempted while the I2C conditions were not valid for a

transmission to be started

0 = No collision

Slave Mode:

1 = The SSPBUF register is written while it is still transmitting the previous word

(must be cleared in software)

0 = No collision

bit 6:

SSPOV: Receive Overflow Indicator bit

In SPI mode

1 = A new byte is received while the SSPBUF register is still holding the previous data. In case of overflow,

the data in SSPSR is lost. Overflow can only occur in slave mode. In slave mode, the user must read the

SSPBUF, even if only transmitting data, to avoid setting overflow. In master mode, the overflow bit is not

set since each new reception (and transmission) is initiated by writing to the SSPBUF register. (Must be

cleared in software).

0 = No overflow

In I2C mode

1 = A byte is received while the SSPBUF register is still holding the previous byte. SSPOV is a "don’t care"

in transmit mode. (Must be cleared in software).

0 = No overflow

bit 5:

SSPEN: Synchronous Serial Port Enable bit

In both modes, when enabled, these pins must be properly configured as input or output.

In SPI mode

1 = Enables serial port and configures SCK, SDO, SDI, and SS as the source of the serial port pins

0 = Disables serial port and configures these pins as I/O port pins

In I2C mode

1 = Enables the serial port and configures the SDA and SCL pins as the source of the serial port pins

0 = Disables serial port and configures these pins as I/O port pins

bit 4:

CKP: Clock Polarity Select bit

In SPI mode

1 = Idle state for clock is a high level

0 = Idle state for clock is a low level

In I2C slave mode

SCK release control

1 = Enable clock

0 = Holds clock low (clock stretch) (Used to ensure data setup time)

In I2C master mode

Unused in this mode

bit 3-0: SSPM3:SSPM0: Synchronous Serial Port Mode Select bits

0000

= SPI master mode, clock = FOSC/4

0001

= SPI master mode, clock = FOSC/16

0010

= SPI master mode, clock = FOSC/64

0011

= SPI master mode, clock = TMR2 output/2

0100

= SPI slave mode, clock = SCK pin. SS pin control enabled.

0101

= SPI slave mode, clock = SCK pin. SS pin control disabled. SS can be used as I/O pin

0110

= I2C slave mode, 7-bit address

0111

= I2C slave mode, 10-bit address

1000

= I2C master mode, clock = FOSC / (4 * (SSPADD+1) )

1xx1

= Reserved

1x1x

= Reserved

PIC16LC773 数据表(PDF) 55 Page - Microchip Technology

PIC16LC773 数据表(HTML) 55 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表下载

链接网址

PIC16LC773 数据表(PDF) 55 Page - Microchip Technology

PIC16LC773 数据表(HTML) 55 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表 下载

链接网址

数据表下载