PC87334VLJ datasheet(86/102 Pages) NSC

86 / 102 page

100 Electrical Characteristics (Continued)

102 DC Electrical Characteristics 33V g10%

ABSOLUTE MAXIMUM RATINGS

(Notes 1 and 2)

If MilitaryAerospace specified devices are required

please contact the National Semiconductor Sales

OfficeDistributors for availability and specifications

Supply Voltage (VDD)

05V to a70V

Input Voltage (VI)

05V to a55V

Output Voltage (VO)

05V to VDD a03V

Storage Temperature (TSTG)

65 Cto a165 C

Power Dissipation (PD)1W

Lead Temperature (TL)

(Soldering 10 seconds)

260 C

RECOMMENDED OPERATING CONDITIONS

Supply Voltage (VDD)

30V to 36V

Operating Temperature (TA)0 Cto70 C

ESD Tolerance

1500V

CZAP e 100 pF

RZAP e 15 kX (Note 3)

CAPACITANCE

TA e 25 C f e 1 MHz

Symbol

Parameter

Min

Typ

Max

Units

CIN

Input Pin Capacitance

CIN1

Clock Input Capacitance

CIO

IO Pin Capacitance

Output Pin Capacitance

DC CHARACTERISTICS

Under Recommended Operating Conditions

Symbol

Parameter

Conditions

Min

Typ

Max

Units

VIH

Input High Voltage

VDD

VIL

Input Low Voltage

ICC

VDD Average Supply Current

VIL e 05V

VIH e 24V

No Load

ICCSB

VDD Quiescent Supply Current

VIL e VSS

(Note 4)

in Low Power Mode

VIH e VDD

No Load

IIL

Input Leakage Current

VIN e VDD

(Note 5)

VIN e VSS

Note 1

Absolute Maximum Ratings are those values beyond which damage to the device may occur

Note 2

Unless otherwise specified all voltages are referenced to ground

Note 3

Value based on test complying with NSC SOP5-028 human body model ESD testing using the ETS-910 tester

Note 4

The parameter ICCSB is guaranteed by characterization Due to test conditions it is not 100% tested ICCSB is measured when UART1 or 2’s FCR bit is 1

Note 5

During reset the MFM pin is rated for 10 mA b150 mA leakage is due to an internal pull-up resistor The RTS1 2 and SOUT1 2 and DTR1 2 and HCS0 1

and IDEHI and VLD01 and IDEHLO are rated for 200 mA b160 mA leakage is due to internal pull-down resistors During normal operation the BUSY PE

and SLCT pins are rated for 100 mA b200 mA leakage is due to internal pull-down resistors The ACK and ERR pins are rated for 10 mA b200 mA

leakage is due to internal pull-up resistors

PC87334VLJ 数据表(PDF) 86 Page - National Semiconductor (TI)

PC87334VLJ 数据表(HTML) 86 Page - National Semiconductor (TI)

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表下载