| 数据搜索系统,热门电子元器件搜索 |
|
AD9268 数据表(PDF) 29 Page - Analog Devices |
|
|
|||||||||||||||||||||||||||||
AD9268 数据表(HTML) 29 Page - Analog Devices |
|
29 / 45 page ![]() AD9268 Rev. A | Page 28 of 44 The signal characteristics must be considered when selecting a transformer. Most RF transformers saturate at frequencies below a few megahertz (MHz). Excessive signal power can also cause core saturation, which leads to distortion. At input frequencies in the second Nyquist zone and above, the noise performance of most amplifiers is not adequate to achieve the true SNR performance of the AD9268. For applications in which SNR is a key parameter, differential double balun coupling is the recommended input configuration (see Figure 68). In this configuration, the input is ac-coupled, and the CML is provided to each input through a 33 Ω resistor. These resistors compensate for losses in the input baluns to provide a 50 Ω impedance to the driver. In the double balun and transformer configurations, the value of the input capacitors and resistors is dependent on the input fre- quency and source impedance and may need to be reduced or removed. Table 10 displays recommended values to set the RC network. At higher input frequencies, good performance can be achieved by using a ferrite bead in series with a resistor and removing the capacitors. However, these values are dependent on the input signal and should be used only as a starting guide. Table 10. Example RC Network Frequency Range (MHz) R1 Series (Ω Each) C1 Differential (pF) R2 Series (Ω Each) C2 Shunt (pF Each) 0 to 100 33 5 15 15 100 to 200 10 5 10 10 100 to 300 101 Remove 66 Remove 1 In this configuration, R1 is a ferrite bead with a value of 10 Ω @ 100 MHz. An alternative to using a transformer-coupled input at fre- quencies in the second Nyquist zone is to use the AD8352 differential driver. An example is shown in Figure 69. See the AD8352 data sheet for more information. AD9268 R1 0.1µF 0.1µF 2V p-p VIN+ VIN– VCM C1 C2 R1 R2 R2 0.1µF S 0.1µF C2 33 Ω 33 Ω S PA P Figure 68. Differential Double Balun Input Configuration AD8352 0 Ω 0 Ω CD RD RG 0.1µF 0.1µF 0.1µF 0.1µF 16 1 2 3 4 5 11 0.1µF 0.1µF 10 14 VCC 0.1µF 8, 13 200 Ω 200 Ω ANALOG INPUT ANALOG INPUT R R C AD9268 VIN+ VIN– VCM Figure 69. Differential Input Configuration Using the AD8352 |
|
链接网址 |
| ALLDATASHEET是否为您带来帮助? [ DONATE ] |
关于 Alldatasheet | 广告服务 | 联系我们 | 隐私政策 | 数据表链接 | 链接交换 | 制造商名单 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |