ADAU1361BCPZ-R7 datasheet(40/80 Pages) AD

40 / 80 page

ADAU1361

Data Sheet

Rev. D | Page 40 of 80

I2C Read and Write Operations

Figure 50 shows the format of a single-word write operation.

Every ninth clock pulse, the ADAU1361 issues an acknowledge

by pulling SDA low.

Figure 51 shows the format of a burst mode write sequence. This

figure shows an example of a write to sequential single-byte

registers. The ADAU1361 increments its subaddress register

after every byte because the requested subaddress corresponds

to a register or memory area with a 1-byte word length.

Figure 52 shows the format of a single-word read operation. Note

that the first R/W bit is 0, indicating a write operation. This is

because the subaddress still needs to be written to set up the

internal address. After the ADAU1361 acknowledges the receipt

of the subaddress, the master must issue a repeated start command

followed by the chip address byte with the R/W bit set to 1 (read).

This causes the ADAU1361 SDA to reverse and begin driving

data back to the master. The master then responds every ninth

pulse with an acknowledge pulse to the ADAU1361.

Figure 53 shows the format of a burst mode read sequence. This

figure shows an example of a read from sequential single-byte

registers. The ADAU1361 increments its subaddress register

after every byte because the requested subaddress corresponds

to a register or memory area with a 1-byte word length. The

ADAU1361 always decodes the subaddress and sets the auto-

increment circuit so that the address increments after the

appropriate number of bytes.

Figure 50 to Figure 53 use the following abbreviations:

S = start bit

P = stop bit

AM = acknowledge by master

AS = acknowledge by slave

Chip address,

R/W = 0

Subaddress high byte

Subaddress low byte

Data Byte 1

Figure 50. Single-Word I2C Write Format

Chip address,

R/W = 0

Subaddress

high byte

Subaddress

low byte

Data

Byte 1

Data

Byte 2

Data

Byte 3

Data

Byte 4

…

Figure 51. Burst Mode I2C Write Format

Chip address,

R/W = 0

Subaddress high

byte

Subaddress low

byte

Chip address,

R/W = 1

Data

Byte 1

Figure 52. Single-Word I2C Read Format

Chip address,

R/W = 0

Subaddress

high byte

Subaddress

low byte

Chip address,

R/W = 1

Data

Byte 1

Data

Byte 2

…

Figure 53. Burst Mode I2C Read Format

ADAU1361BCPZ-R7 数据表(PDF) 40 Page - Analog Devices

ADAU1361BCPZ-R7 数据表(HTML) 40 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80

数据表下载

链接网址

ADAU1361BCPZ-R7 数据表(PDF) 40 Page - Analog Devices

ADAU1361BCPZ-R7 数据表(HTML) 40 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80

数据表 下载

链接网址

数据表下载