 |
数据搜索系统，热门电子元器件搜索 |
|
|
数据搜索系统，热门电子元器件搜索 |
|
STM32F373VC 数据表(PDF) 91 Page - STMicroelectronics |
|
|
|||||||||||||||||||||||||||||
STM32F373VC 数据表(HTML) 91 Page - STMicroelectronics |
|
|
91 / 137 page  DocID022691 Rev 7 91/137 STM32F373xx Electrical characteristics 114 6.3.16 Communications interfaces I2C interface characteristics The I2C interface meets the requirements of the standard I2C communication protocol with the following restrictions: the I/O pins SDA and SCL are mapped to are not “true” open- drain. When configured as open-drain, the PMOS connected between the I/O pin and VDD is disabled, but is still present. The I2C characteristics are described in Table 56. Refer also to Section 6.3.14: I/O port characteristics for more details on the input/output alternate function characteristics (SDA and SCL). Table 56. I2C characteristics(1) Symbol Parameter Standard Fast mode Fast mode + Unit Min Max Min Max Min Max fSCL SCL clock frequency 0 100 0 400 0 1000 KHz tLOW Low period of the SCL clock 4.7 - 1.3 - 0.5 - µs tHIGH High Period of the SCL clock 4 - 0.6 - 0.26 - µs tr Rise time of both SDA and SCL signals - 1000 - 300 - 120 ns tf Fall time of both SDA and SCL signals - 300 - 300 - 120 ns tHD;DAT Data hold time 0 - 0 - 0 - µs tVD;DAT Data valid time - 3.45(2) -0.9(2) -0.45(2) µs tVD;ACK Data valid acknowledge time - 3.45(2) -0.9(2) -0.45(2) µs tSU;DAT Data setup time 250 - 100 - 50 - ns tHD;STA Hold time (repeated) START condition 4.0 - 0.6 - 0.26 - µs tSU;STA Set-up time for a repeated START condition 4.7 - 0.6 - 0.26 - µs tSU;STO Set-up time for STOP condition 4.0 - 0.6 - 0.26 - µs tBUF Bus free time between a STOP and START condition 4.7 - 1.3 - 0.5 - µs Cb Capacitive load for each bus line - 400 - 400 - 550 pF 1. The I2C characteristics are the requirements from the I2C bus specification rev03. They are guaranteed by design when the I2Cx_TIMING register is correctly programmed (refer to reference manual). These characteristics are not tested in production. 2. The maximum tHD;DAT could be 3.45 µs, 0.9 µs and 0.45 µs for standard mode, fast mode and fast mode plus, but must be less than the maximum of tVD;DAT or tVD;ACK by a transition time. |
|
链接网址 |
| ALLDATASHEET是否为您带来帮助? [ DONATE ] |
关于 Alldatasheet | 广告服务 | 联系我们 | 隐私政策 | 数据表链接 | 链接交换 | 制造商名单 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |
Chinese ▼
English
Chinese
German
Japanese
Russian
Korean
Spanish
French
Italian
Portuguese
Polish
Vietnamese
Indian
Mexican
British
New Zealand
