Ultracompact, 1.5 A Thermoelectric Cooler

(TEC) Controller

Data Sheet

ADN8834

Rev. B

Document Feedback

Information furnished by Analog Devices is believed to be accurate and reliable. However, no

responsibilityisassumedbyAnalogDevicesforitsuse,norforanyinfringementsofpatentsorother

rightsofthirdpartiesthatmayresultfromitsuse.Specificationssubjecttochangewithoutnotice.No

license is granted by implication or otherwise under any patent or patent rights of Analog Devices.

Trademarksandregisteredtrademarksarethepropertyoftheirrespectiveowners.

One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.

Tel: 781.329.4700

©2015–2018 Analog Devices, Inc. All rights reserved.

Technical Support

www.analog.com

FEATURES

Patented high efficiency single inductor architecture

Integrated low R

TEC voltage and current operation monitoring

No external sense resistor required

Independent TEC heating and cooling current limit settings

Programmable maximum TEC voltage

2.0 MHz PWM driver switching frequency

External synchronization

Two integrated, zero drift, rail-to-rail chopper amplifiers

Capable of NTC or RTD thermal sensors

2.50 V reference output with 1% accuracy

Temperature lock indicator

Available in a 25-ball, 2.5 mm × 2.5 mm WLCSP or in a

24-lead, 4 mm × 4 mm LFCSP

APPLICATIONS

TEC temperature control

Optical modules

Optical fiber amplifiers

Optical networking systems

Instruments requiring TEC temperature control

FUNCTIONAL BLOCK DIAGRAM

TEC CURRENT

AND VOLTAGE

SENSE AND LIMIT

CONTROLLER

LINEAR

POWER

STAGE

TEC DRIVER

PWM

POWER

STAGE

OSCILLATOR

VOLTAGE

REFERENCE

OUT1

VLIM/

SD

VTEC

ILIM

PVIN

ITEC

EN/SY

VREF

LDR

SFB

IN2P

IN2N

IN1P

IN1N

OUT2

SW

PGNDx

VDD

AGND

ERROR

AMP

COMP

AMP

Figure 1.

GENERAL DESCRIPTION

The ADN88341 is a monolithic TEC controller with an integrated

TEC controller. It has a linear power stage, a pulse-width

modulation (PWM) power stage, and two zero-drift, rail-to-rail

operational amplifiers. The linear controller works with the PWM

driver to control the internal power MOSFETs in an H-bridge

configuration. By measuring the thermal sensor feedback

voltage and using the integrated operational amplifiers as a

proportional integral differential (PID) compensator to condition

the signal, the ADN8834 drives current through a TEC to settle

the temperature of a laser diode or a passive component attached

to the TEC module to the programmed target temperature.

The ADN8834 supports negative temperature coefficient (NTC)

thermistors as well as positive temperature coefficient (PTC)

resistive temperature detectors (RTD). The target temperature is

set as an analog voltage input either from a digital-to-analog

converter (DAC) or from an external resistor divider.

The temperature control loop of the ADN8834 is stabilized by

PID compensation utilizing the built in, zero drift chopper

amplifiers. The internal 2.50 V reference voltage provides a 1%

accurate output that is used to bias a thermistor temperature

sensing bridge as well as a voltage divider network to program

the maximum TEC current and voltage limits for both the heating

and cooling modes. With the zero drift chopper amplifiers,

extremely good long-term temperature stability is maintained via

an autonomous analog temperature control loop.

Table 1. TEC Family Models

Device No.

MOSFET

Thermal Loop

Package

ADN8831

Discrete

Digital/analog

LFCSP (CP-32-7)

ADN8833

Integrated

Digital

WLCSP (CB-25-7),

LFCSP (CP-24-15)

ADN8834

Integrated

Digital/analog

WLCSP (CB-25-7),

LFCSP (CP-24-15)