Data Sheet

ADE7912/ADE7913

Rev. C | Page 7 of 41

REGULATORY APPROVALS

The ADE7912/ADE7913 are approved by the organizations listed in Table 2. Refer to Table 8 and the Insulation Lifetime section for more

information about the recommended maximum working voltages for specific cross-isolation waveforms and insulation levels.

Note that Table 8 presents the maximum working voltages for 50-year minimum lifetime: 400 V rms for ac voltages and 1173 V peak for

dc voltages. Greater working voltages shorten the lifetime of the product (see the Insulation Lifetime section). Some certifications in

Table 2 state greater maximum working voltages than the values presented in Table 8. Therefore, use the ADE7912/ADE7913 only for

working voltages lower than those presented in Table 8 (400 V rms for ac voltages and 1173 V peak for dc voltages).

Table 2. Regulatory Approvals

UL

CSA

VDE

Recognized Under

UL 1577 Component

Basic insulation per CSA 60950-1-07+A1+A2, CSA 62368-1-14, and IEC 60950-1

Certified according to

(VDE V 0884-10):2006-12

Single Protection,

5000 V rms Isolation

Voltage

clauses K.3, K.4, 6.7.1.3, 6.7.2.2.2 A.17, K.6x1.6, and K.7x1.6, 10. The risk management

process is not applicable to these clauses (Pollution Degree 2, Material Group III,

Overvoltage Category II, III, and IV):

Reinforced insulation,

Approved under

CSA Component

Acceptance Notice 5A

Ed.+A1+A2, and IEC 62368-1:2014 Ed. 2 (Pollution Degree 2, Material Group III):

415 V rms (586 V peak) maximum working voltage.

IEC 61010-1 C1 14.1 a) for use in IEC 61010-1 end products because the ADE7912/

ADE7913 meet the requirements of the IEC 62368-1 evaluation (Pollution Degree 2,

Material Group III, and Overvoltage Category II and III):

300 V rms (424 V peak) maximum working voltage.

FILE E214100

FILE 2758945

FILE 2471900-4880-0001

1

In accordance with UL 1577, each ADE7912/ADE7913 is proof tested by applying an insulation test voltage ≥6000 V rms for 1 second (current leakage detection limit = 15 µA).

2

At this maximum working voltage, the approximate predicted lifetime is 0.2 years under 50 Hz, 60 Hz ac voltages.

3

In accordance with DIN V VDE V 0884-10, each ADE7912/ADE7913 is proof tested by applying an insulation test voltage ≥1590 V peak for 1 second (partial discharge

detection limit = 5 pC). The asterisk (*) marking branded on the component designates DIN VDE V 0884-10 (VDE V 0884-10):2006-12 approval.

4

At this maximum working voltage, the approximate predicted lifetime is 8 years under 50 Hz, 60 Hz ac voltages.

5

At this maximum working voltage, the approximate predicted lifetime is 8 years under 50 Hz, 60 Hz ac voltages.

INSULATION AND SAFETY RELATED SPECIFICATIONS

Table 3. Critical Safety Related Dimensions and Material Properties

Parameter

Symbol

Value

Unit

Test Conditions/Comments

Rated Dielectric Insulation Voltage

5000

V rms

1-minute duration

Minimum External Air Gap (Clearance)

L(l01)

8.3

mm

Distance measured from input terminals to output

terminals, shortest distance through air along the

PCB mounting plane, as an aid to PCB layout

Minimum External Tracking (Creepage)

L(l02)

8.3

mm

Measured from input terminals to output terminals,

shortest distance path along body

Minimum Internal Gap (Internal Clearance)

0.017 min

mm

Insulation distance through insulation

Tracking Resistance (Comparative Tracking Index)

CTI

400

V

IEC 60112

Isolation Group

II

Material group (DIN VDE 0110, 1/89, Table 1)