DVR datasheet(79/416 Pages) MICROCHIP

79 / 416 page

 2016-2018 Microchip Technology Inc.

DS30010118D-page 79

PIC24FJ256GA705 FAMILY

7.0

RESETS

The Reset module combines all Reset sources and

controls the device Master Reset Signal, SYSRST. The

following is a list of device Reset sources:

• POR: Power-on Reset

•MCLR: Master Clear Pin Reset

•SWR: RESET Instruction

• WDT: Watchdog Timer Reset

• BOR: Brown-out Reset

• CM: Configuration Mismatch Reset

• TRAPR: Trap Conflict Reset

• IOPUWR: Illegal Opcode Reset

• UWR: Uninitialized W Register Reset

A simplified block diagram of the Reset module is

shown in Figure 7-1.

Any active source of Reset will make the SYSRST

signal active. Many registers associated with the CPU

and peripherals are forced to a known Reset state.

Most registers are unaffected by a Reset; their status is

unknown on POR and unchanged by all other Resets.

All types of device Reset will set a corresponding status

bit in the RCON register to indicate the type of Reset

(see Register 7-1). A POR will clear all bits, except for

the BOR and POR (RCON<1:0>) bits, which are set.

The user may set or clear any bit at any time during

code execution. The RCON bits only serve as status

bits. Setting a particular Reset status bit in software will

not cause a device Reset to occur.

The RCON register also has other bits associated with

the Watchdog Timer and device power-saving states.

The function of these bits is discussed in other sections

of this data sheet.

FIGURE 7-1:

RESET SYSTEM BLOCK DIAGRAM

Note:

This data sheet summarizes the features

of this group of PIC24F devices. It is not

intended to be a comprehensive refer-

ence source. For more information, refer

to the “dsPIC33/PIC24 Family Reference

Manual”, “Reset” (DS39712), which is

available from the Microchip website

(www.microchip.com). The information

in this data sheet supersedes the

information in the FRM.

Note:

Refer to the specific peripheral or CPU

section of this manual for register Reset

states.

Note:

The status bits in the RCON register

should be cleared after they are read so

that the next RCON register values after a

device Reset will be meaningful.

MCLR

VDD

VDD Rise

Detect

POR

Sleep or Idle

Brown-out

Reset

Enable Voltage Regulator

RESET

Instruction

WDT

Module

Glitch Filter

BOR

Trap Conflict

Illegal Opcode

Uninitialized W Register

SYSRST

Configuration Mismatch

DVR 数据表(PDF) 79 Page - Microchip Technology

DVR 数据表(HTML) 79 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表下载

链接网址

DVR 数据表(PDF) 79 Page - Microchip Technology

DVR 数据表(HTML) 79 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表 下载

链接网址

数据表下载