DVR datasheet(140/416 Pages) MICROCHIP

140 / 416 page

PIC24FJ256GA705 FAMILY

DS30010118D-page 140

 2016-2018 Microchip Technology Inc.

11.5.5

CONSIDERATIONS FOR

PERIPHERAL PIN SELECTION

The ability to control Peripheral Pin Selection intro-

duces several considerations into application design

that could be overlooked. This is particularly true for

several common peripherals that are available only as

remappable peripherals.

The main consideration is that the Peripheral Pin

Selects are not available on default pins in the device’s

default (Reset) state. Since all RPINRx registers reset

to ‘111111’ and all RPORx registers reset to ‘000000’,

all Peripheral Pin Select inputs are tied to VSS, and all

Peripheral Pin Select outputs are disconnected.

This situation requires the user to initialize the device

with the proper peripheral configuration before any

other application code is executed. Since the IOLOCK

bit resets in the unlocked state, it is not necessary to

execute the unlock sequence after the device has

come out of Reset. For application safety, however, it is

best to set IOLOCK and lock the configuration after

writing to the control registers.

Because the unlock sequence is timing-critical, it must

be executed as an assembly language routine in the

same manner as changes to the oscillator configura-

tion. If the bulk of the application is written in ‘C’, or

another high-level language, the unlock sequence

should be performed by writing in-line assembly.

Choosing the configuration requires the review of all

Peripheral Pin Selects and their pin assignments,

especially those that will not be used in the application.

In all cases, unused pin-selectable peripherals should

be disabled completely. Unused peripherals should

have their inputs assigned to an unused RPn/RPIn pin

function. I/O pins with unused RPn functions should be

configured with the null peripheral output.

The assignment of a peripheral to a particular pin does

not automatically perform any other configuration of the

pin’s I/O circuitry. In theory, this means adding a pin-

selectable output to a pin may mean inadvertently

driving an existing peripheral input when the output is

driven. Users must be familiar with the behavior of

other fixed peripherals that share a remappable pin and

know when to enable or disable them. To be safe, fixed

digital peripherals that share the same pin should be

disabled when not in use.

Along these lines, configuring a remappable pin for a

specific peripheral does not automatically turn that fea-

ture on. The peripheral must be specifically configured

for operation and enabled as if it were tied to a fixed pin.

Where this happens in the application code (immediately

following a device Reset and peripheral configuration or

inside the main application routine) depends on the

peripheral and its use in the application.

A final consideration is that Peripheral Pin Select func-

tions neither override analog inputs nor reconfigure

pins with analog functions for digital I/Os. If a pin is

configured as an analog input on a device Reset, it

must be explicitly reconfigured as a digital I/O when

used with a Peripheral Pin Select.

Example 11-4 shows a configuration for bidirectional

communication with flow control using UART1. The

following input and output functions are used:

• Input Functions: U1RX, U1CTS

• Output Functions: U1TX, U1RTS

EXAMPLE 11-4:

CONFIGURING UART1

INPUT AND OUTPUT

FUNCTIONS

// Unlock Registers

asm volatile

("MOV

#OSCCON, w1

\n"

"MOV

#0x46, w2

\n"

"MOV

#0x57, w3

\n"

"MOV.b w2, [w1]

\n"

"MOV.b w3, [w1]

\n"

"BCLR

OSCCON, #6")

;

// or use XC16 built-in macro:

// __builtin_write_OSCCONL(OSCCON & 0xbf);

// Configure Input Functions (Table 11-6)

// Assign U1RX To Pin RP0

RPINR18bits.U1RXR = 0;

// Assign U1CTS To Pin RP1

RPINR18bits.U1CTSR = 1;

// Configure Output Functions (Table 11-7)

// Assign U1TX To Pin RP2

RPOR1bits.RP2R = 3;

// Assign U1RTS To Pin RP3

RPOR1bits.RP3R = 4;

// Lock Registers

asm volatile

("MOV

#OSCCON, w1

\n"

"MOV

#0x46, w2

\n"

"MOV

#0x57, w3

\n"

"MOV.b w2, [w1]

\n"

"MOV.b w3, [w1]

\n"

"BSET

OSCCON, #6")

;

// or use XC16 built-in macro:

// __builtin_write_OSCCONL(OSCCON | 0x40);

DVR 数据表(PDF) 140 Page - Microchip Technology

DVR 数据表(HTML) 140 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表下载

链接网址

DVR 数据表(PDF) 140 Page - Microchip Technology

DVR 数据表(HTML) 140 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表 下载

链接网址

数据表下载