PCF5083HSLASHF2 datasheet(40/136 Pages) PHILIPS

40 / 136 page

1996 Oct 29

Philips Semiconductors

Objective speciﬁcation

GSM signal processing IC

PCF5083

8.5.4

MONITOR CHANNEL RECEIVER PROTOCOL

• After IOMCON_REG[MASTERx_EN] is set to a logic 1,

the receiver state machine is in an idle state and waits

for the first byte transmission. The input buffer full flag

MONx_IBF is cleared. The MR flag is sent as a logic 1

in accordance with the IOM®-2 specification.

• After the reception of a data byte the MONx_IBF flag is

set and the System Controller may read the data from

MONx_REG.

• A full handshake is implemented in accordance with

IOM®-2 specification. The receiver may delay the data

transmission if the input buffer is full and the System

Controller does not read the buffer in time. In this case

MR = 0 is maintained until MONx_REG is read. The

MONx_IBF flag is cleared with the data read access.

The transmitter may delay the data transmission if it

delays the next byte valid indication. In this case MR = 0

is maintained in subsequent frames.

• If an end of transmission is detected the receiver state

machine gets into the idle state. The REOMx flag in

IOMCTRL_REG is set. REOMx = 1 also asserts the

IOM®-2 interrupt (IOMx_IBF_EN is used as enable bit)

to indicate the end of transmission to the System

Controller. The REOMx flag is cleared with a dummy

read of MONx_REG.

• To send an abort request the TABORTx flag in

IOMCTRL_REG is set. The receiver state machine

enters the idle state. The TABORTx flag is reset after the

procedure.

Time-outs are not detected. Collision detection and the

maximum speed case is not supported.

8.5.5

COMMAND/INDICATION CHANNEL TRANSMITTER

All data words are sent at least in two subsequent frames.

If the transmitter runs out of data the last data word is

repeated. The flags CI0(1)_IBF and CI0(1)_OBE are

provided to indicate the input/output register status.

8.5.6

COMMAND/INDICATION CHANNEL RECEIVER

If the received data is different from the data input buffer

the new data pattern is loaded into the data input buffer.

The CI0(1)_IBF flag is cleared if it is set. If during the next

frame the received data is identical to the data stored in the

data input buffer the buffer contents is considered valid

and the CI0(1)_IBF flag is set. The System Controller now

has to fetch the data within the next 125

µs, otherwise data

might be lost.

8.5.7

AUDIO INTERFACE

The Audio Interface provides the translation of one 16-bit

IOM®-2 timeslot into a timing according to Chapter 16 for

the receive and transmit direction. The operation of the

interface is configurable with the flags of register

ACON_REG. The Audio Interface is enabled or disabled

under control of the DSP core with IO1/AEN = 1.

Otherwise the data word 00H is sent in both directions.

With ACON_REG[TRANS_EN] = 1, a transparent mode is

selected. In this mode the internal IOM®-2 signals FSC

and DCL are directly connected to ACLK and AFS. ADI is

directly connected to A_OUT or B_OUT and ADO to A_IN

or B_IN.

The following should be noted:

• The flags in register ACON_REG should only be

changed when the Audio Interface is disabled with

IO1/AEN = 0

• The Audio Interface can only operate in the transparent

mode if a timing mode is selected which results in only

one 16-bit timeslot on the IOM®-2 side

• The frequency of ACLK must be chosen such that the

complete transmission of a 16-bit word via the Audio

Interface does not exceed the duration of N-1 timeslots,

with N equal to the number of 16-bit timeslots on the

IOM®-2 side

• Jitter is not allowed on AFS and ACLK as audio data

might get corrupted.

Table 25 Audio Interface conﬁguration register (ACON_REG)

BIT

FLAG

OPERATION (if bit is set)

TX_EN

Enable transmit direction (ADI to IOM®-2).

TX_DEST

Select output to IOM®-2. A logic 0 selects A_OUT; a logic 1 selects B_OUT.

RX_EN

Enable receive direction (IOM®-2 to ADO).

RX_SOURCE

Select input from IOM®-2. A logic 0 selects A_IN; a logic 1 selects B_IN.

4 to 7

TX_SLOT0 to TX_SLOT3

IOM®-2 timeslot translated from the transmit section (0 to 15).

8 to 11

RX_SLOT0 to RX_SLOT3

IOM®-2 timeslot translated from the receive section (0 to 15).

TRANS_EN

Enable transparent mode.

PCF5083H/F2 数据表(PDF) 40 Page - NXP Semiconductors

PCF5083H/F2 数据表(HTML) 40 Page - NXP Semiconductors

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表下载