PCF5083HSLASHF2 datasheet(30/136 Pages) PHILIPS

30 / 136 page

1996 Oct 29

Philips Semiconductors

Objective speciﬁcation

GSM signal processing IC

PCF5083

A power-down line is only deactivated during Sleep mode

if the corresponding activation register is programmed with

a higher value than register SLEEPCNT_REG. Otherwise

the power-down line stays active during Sleep mode. The

output polarity of the power-down lines can be changed by

setting their corresponding bit in register POL_REG to a

logic 1. The signals can be clamped to a level depending

on their flag in POL_REG by setting the corresponding bit

in register MASK_REG to a logic 0.

Because the 13 MHz clock is also internally disabled

during Sleep mode, the PCF5083 cannot be accessed

with the host port.

During Sleep mode, burst timing and frame interrupt

generation is stopped and the registers MODE0_REG and

MODE1_REG are cleared.

8.3.3.1

Transceiver control lines

The timing generator signals RXON, TXON, BEN, PDRX1,

PDRX2, PDTX1, NPDTX1, NPDTX2, PDBIAS, NPDBIAS,

PDSYN, TXKEY1, TXKEY2 and the RF device control bus

signals RFCLK, RFDO, RFEN1 to RFEN4, RFE and the

Voice Port signals ASF, ACLK and ADO are 3-stated as

long as the signal GPON1 is inactive during Sleep mode.

The signals are driven into their high-impedance state

independently of the actual polarity to which GPON1 is

programmed, unless MASK_REG[GPON1] = 0. In this

case the outputs are driven during Sleep mode.

8.3.3.2

The Sleep Quarterbit Counter

In Sleep mode, the 13 MHz reference oscillator is switched

off to reduce the power consumption. The TDMA timing is

maintained using the sleep quarterbit counter (SQBC),

which is driven from the sleep clock (SLCLK). The sleep

clock is derived from the 32.768 kHz real time clock. Upon

entering Sleep mode, the contents of the quarterbit

counter are copied to the sleep quarterbit counter. After

the end of a Sleep mode period, the sleep quarterbit

counter is copied back to the quarterbit counter and normal

timing is performed again.

To maintain the correct timing over hundreds of TDMA

frames, the sleep quarterbit counter is incremented with

the value SQBC_INC equal to the clock ratio between the

quarterbit clock and the sleep clock. This value must be

very accurate and can be derived using the calibration

method described in Section 8.3.3.3.

Fig.10 Quarterbit counters for normal and Sleep mode.

handbook, full pagewidth

MGE289

QBCCTRL_REG[SLEEP]

QBCCTRL_REG[CAL]

13 MHz

1.08325 MHz

32768 Hz

SLCLK

8192 Hz

÷ 4

÷ 12

QBC

(0 to 4999)

TIMING

GENERATOR

NORMAL

MODE

SQBC

RXON

Enter normal mode:

Copy SQBC to QBC

reduced

sleep

mode

Enter sleep mode:

Copy QBC to SQBC

SQBC_INC

(0 to 255)

typ. 123

1083

8.192

TXON

BEN

PDRX1,2

(N)PDTX1,2

SYNON

(N)PDBIAS

TXKEY1,2

TIMING

GENERATOR

SLEEP

MODE

GPON1

GPON2

DSPON

REFON

NREFON

PCF5083H/F2 数据表(PDF) 30 Page - NXP Semiconductors

PCF5083H/F2 数据表(HTML) 30 Page - NXP Semiconductors

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表下载