ST10C167 datasheet(13/65 Pages) STMICROELECTRONICS

13 / 65 page

ST10C167

13/65

VI - EXTERNAL BUS CONTROLLER

All of the external memory accesses are per-

formed by the on-chip external bus controller. The

EBC can be programmed to single chip mode

when no external memory is required, or to one of

four different external memory access modes:

– 16-/18-/20-/24-bit addresses and 16-bit data,

demultiplexed.

– 16-/18-/20-/24-bit addresses and 16-bit data,

multiplexed.

– 16-/18-/20-/24-bit addresses and 8-bit data,

multiplexed.

– 16-/18-/20-/24-bit addresses and 8-bit data, de-

multiplexed.

In demultiplexed bus modes addresses are output

on Port1 and data is input/output on Port0 or P0L,

respectively. In the multiplexed bus modes both

addresses and data use Port0 for input/output.

Timing characteristics of the external bus inter-

face (memory cycle time, memory tri-state time,

length of ALE and read/write delay) are program-

mable giving the choice of a wide range of memo-

ries and external peripherals. Up to 4 independent

address windows may be defined (using register

pairs ADDRSELx / BUSCONx) to access different

resources and bus characteristics. These address

windows

are

arranged

hierarchically

where

BUSCON4 overrides BUSCON3 and BUSCON2

overrides BUSCON1. All accesses to locations

not covered by these 4 address windows are con-

trolled by BUSCON0. Up to 5 external CS signals

(4 windows plus default) can be generated in

order to save external glue logic. Access to very

slow memories is supported by a ‘Ready’ function.

A HOLD/HLDA protocol is available for bus arbi-

tration which shares external resources with other

bus masters. The bus arbitration is enabled by

setting bit HLDEN in register SYSCON. After set-

ting HLDEN once, pins P6.7...P6.5 (BREQ,

HLDA, HOLD) are automatically controlled by the

EBC. In master mode (default after reset) the

HLDA pin is an output. By setting bit DP6.7 to’1’

the slave mode is selected where pin HLDA is

switched to input. This directly connects the slave

controller to another master controller without

glue logic.

For applications which require less external mem-

ory space, the address space can be restricted to

1M Byte, 256K Byte or to 64K Byte. Port 4 outputs

all 8 address lines if an address space of

16M Byte is used, otherwise four, two or no

address lines.

Chip select timing can be made programmable.

By default (after reset), the CSx lines change half

a CPU clock cycle after the rising edge of ALE.

With the CSCFG bit set in the SYSCON register

the CSx lines change with the rising edge of ALE.

The active level of the READY pin can be set by

bit RDYPOL in the BUSCONx registers. When the

READY function is enabled for a specific address

window, each bus cycle within the window must

be terminated with the active level defined by bit

RDYPOL in the associated BUSCON register.

ST10C167 数据表(PDF) 13 Page - STMicroelectronics

ST10C167 数据表(HTML) 13 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65

数据表下载

链接网址

ST10C167 数据表(PDF) 13 Page - STMicroelectronics

ST10C167 数据表(HTML) 13 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65

数据表 下载

链接网址

数据表下载