ST20C2 datasheet(22/212 Pages) STMICROELECTRONICS

22 / 212 page

22/212

If the process state registers are referred to without subscripts then the current priority

is implied.

3.1.2

Other machine registers

There are several other registers which the programmer should know about, but which

are not part of the process state. These are presented in Table 3.3.

Enables register

The Enables register contains:

• TrapEnables bits (0..15) which can be used to control the taking of traps;

• GlobalInterruptEnables bits (16..31) which are used to control timeslicing and

interruptibility. These are normally set to 1.

Bits of

TrapEnables may be set using the trapenb instruction and cleared using

trapdis. Bits of GlobalInterruptEnables may be set using the instruction gintenb and

disabled using

gintdis.

The contents of the Enables register are shown in Table 3.4.

ClockEnables

ClockEnables is a pair of flags which enab le the timers ClockReg to tick. Bit zero of

ClockEnables controls ClockReg[0] and bit 1 controls ClockReg[1]. In each case,

full name / description

ProcQueueFPtr[0]

high priority front pointer register - contains pointer to first process on the high

priority scheduling list

ProcQueueFPtr[1]

low priority front pointer register - contains pointer to first process on the low

priority scheduling list

ProcQueueBPtr[0]

high priority back pointer register - contains pointer to last process on the high

priority scheduling list

ProcQueueBPtr[1]

low priority back pointer register - contains pointer to last process on the low

priority scheduling list

ClockReg[0]

high priority clock register - contains current value of high priority clock

ClockReg[1]

low priority clock register - contains current value of low priority clock

TptrReg[0]

high priority timer list pointer register - contains pointer to the first process on

the high priority timer list

TptrReg[1]

low priority timer list pointer register - contains pointer to the first process on the

low priority timer list

TnextReg[0]

high priority alarm register - contains the time of the first process on the high

priority timer queue

TnextReg[1]

low priority alarm register - contains the time of the first process on the low

priority timer queue

Enables

trap and global interrupt enables register

Table 3.3 Other machine registers

ST20C2 数据表(PDF) 22 Page - STMicroelectronics

ST20C2 数据表(HTML) 22 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表下载

链接网址

ST20C2 数据表(PDF) 22 Page - STMicroelectronics

ST20C2 数据表(HTML) 22 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表 下载

链接网址

数据表下载