 |
数据搜索系统，热门电子元器件搜索 |
|
|
数据搜索系统，热门电子元器件搜索 |
|
9202 数据表(PDF) 108 Page - STMicroelectronics |
|
|
|||||||||||||||||||||||||||||
9202 数据表(HTML) 108 Page - STMicroelectronics |
|
|
108 / 175 page  UPSD3254A, UPSD3254BV, UPSD3253B, UPSD3253BV 108/175 Table 85. Instructions Note: 1. All bus cycles are WRITE bus cycles, except the ones with the “Read” label 2. All values are in hexadecimal: X = Don’t care. Addresses of the form XXXXh, in this table, must be even addresses RA = Address of the memory location to be read RD = Data READ from location RA during the READ cycle PA = Address of the memory location to be programmed. Addresses are latched on the falling edge of WRITE Strobe (WR, CNTL0). PA is an even address for PSD in Word Programming Mode. PD = Data word to be programmed at location PA. Data is latched on the rising edge of WRITE Strobe (WR , CNTL0) SA = Address of the sector to be erased or verified. The Sector Select (FS0-FS7 or CSBOOT0-CSBOOT3) of the sector to be erased, or verified, must be Active (High). 3. Sector Select (FS0-FS7 or CSBOOT0-CSBOOT3) signals are active High, and are defined in PSDsoft Express. 4. Only address Bits A11-A0 are used in instruction decoding. 5. No Unlock or instruction cycles are required when the device is in the READ Mode 6. The RESET instruction is required to return to the READ Mode after reading the Sector Protection Status, or if the Error Flag Bit (DQ5/DQ13) goes High. 7. Additional sectors to be erased must be written at the end of the Sector Erase instruction within 80µs. 8. The data is 00h for an unprotected sector, and 01h for a protected sector. In the fourth cycle, the Sector Select is active, and (A1,A0)=(1,0) 9. The Unlock Bypass instruction is required prior to the Unlock Bypass Program instruction. 10. The Unlock Bypass Reset Flash instruction is required to return to reading memory data when the device is in the Unlock Bypass Mode. 11. The system may perform READ and Program cycles in non-erasing sectors, read the Flash ID or read the Sector Protection Status when in the Suspend Sector Erase Mode. The Suspend Sector Erase instruction is valid only during a Sector Erase cycle. 12. The Resume Sector Erase instruction is valid only during the Suspend Sector Erase Mode. 13. The MCU cannot invoke these instructions while executing code from the same Flash memory as that for which the instruction is intended. The MCU must retrieve, for example, the code from the secondary Flash memory when reading the Sector Protection Status of the primary Flash memory. Instruction FS0-FS7 or CSBOOT0- CSBOOT3 Cycle 1 Cycle 2 Cycle 3 Cycle 4 Cycle 5 Cycle 6 Cycle 7 READ(5) 1 “Read” RD @ RA READ Sector Protection(6,8,13) 1 AAh@ X555h 55h@ XAAAh 90h@ X555h Read status @ XX02h Program a Flash Byte(13) 1 AAh@ X555h 55h@ XAAAh A0h@ X555h PD@ PA Flash Sector Erase(7,13) 1 AAh@ X555h 55h@ XAAAh 80h@ X555h AAh@ X555h 55h@ XAAAh 30h@ SA 30h7@ next SA Flash Bulk Erase(13) 1 AAh@ X555h 55h@ XAAAh 80h@ X555h AAh@ X555h 55h@ XAAAh 10h@ X555h Suspend Sector Erase(11) 1 B0h@ XXXXh Resume Sector Erase(12) 1 30h@ XXXXh RESET(6) 1 F0h@ XXXXh Unlock Bypass 1 AAh@ X555h 55h@ XAAAh 20h@ X555h Unlock Bypass Program(9) 1 A0h@ XXXXh PD@ PA Unlock Bypass Reset(10) 1 90h@ XXXXh 00h@ XXXXh |
|
链接网址 |
| ALLDATASHEET是否为您带来帮助? [ DONATE ] |
关于 Alldatasheet | 广告服务 | 联系我们 | 隐私政策 | 数据表链接 | 链接交换 | 制造商名单 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |
Chinese ▼
English
Chinese
German
Japanese
Russian
Korean
Spanish
French
Italian
Portuguese
Polish
Vietnamese
Indian
Mexican
British
New Zealand
