| 数据搜索系统,热门电子元器件搜索 |
|
A14100A-RQ208C 数据表(PDF) 14 Page - Actel Corporation |
|
|
|||||||||||||||||||||||||||||
A14100A-RQ208C 数据表(HTML) 14 Page - Actel Corporation |
|
14 / 68 page ![]() 1-188 5V Operating Conditions Absolute Maximum Ratings 1 Free air temperature range Recommended Operating Conditions Electrical Specifications Symbol Parameter Limits Units VCC DC Supply Voltage –0.5 to +7.0 V VI Input Voltage –0.5 to VCC +0.5 V VO Output Voltage –0.5 to VCC +0.5 V IIO I/O Source Sink Current2 ±20 mA TSTG Storage Temperature –65 to +150 °C Notes: 1. Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. Exposure to absolute maximum rated conditions for extended periods may affect device reliability. Device should not be operated outside the Recommended Operating Conditions. 2. Device inputs are normally high impedance and draw extremely low current. However, when input voltage is greater than VCC + 0.5 V or less than GND – 0.5 V, the internal protection diodes will forward bias and can draw excessive current. Parameter Commercial Industrial Military Units Temperature Range1 0 to +70 –40 to +85 –55 to +125 °C 5V Power Supply Tolerance ±5 ±10 ±10 %VCC Note: 1. Ambient temperature (TA) is used for commercial and industrial; case temperature (TC) is used for military. Symbol Parameter Test Condition Commercial Industrial Military Units Min. Max. Min. Max. Min. Max. VOH 1,2 HIGH Level Output IOH = –4 mA (CMOS) 3.7 3.7 V IOH = –6 mA (CMOS) 3.84 V IOH = –10 mA (TTL) 3 2.40 V VOL 1,2 LOW Level Output IOL = +6 mA (CMOS) 0.33 0.4 0.4 V IOL = +12 mA (TTL) 3 0.50 V VIH HIGH Level Input TTL Inputs 2.0 VCC + 0.3 2.0 VCC + 0.3 2.0 VCC + 0.3 V VIL LOW Level Input TTL Inputs –0.3 0.8 –0.3 0.8 –0.3 0.8 V IIN Input Leakage VI = VCC or GND –10 +10 –10 +10 –10 +10 µA IOZ 3-state Output Leakage VO = VCC or GND –10 +10 –10 +10 –10 +10 µA CIO I/O Capacitance3,4 10 10 10 pF ICC(S) Standby VCC Supply Current (typical = 0.7 mA) 2 10 20 mA ICC(D) Dynamic VCC Supply Current See “Power Dissipation” Section Notes: 1. Actel devices can drive and receive either CMOS or TTL signal levels. No assignment of I/Os as TTL or CMOS is required. 2. Tested one output at a time, VCC = min. 3. Not tested, for information only. 4. VOUT = 0V, f = 1 MHz. 5. Typical standby current = 0.7 mA. All outputs unloaded. All inputs = VCC or GND. |
|
链接网址 |
| ALLDATASHEET是否为您带来帮助? [ DONATE ] |
关于 Alldatasheet | 广告服务 | 联系我们 | 隐私政策 | 数据表链接 | 链接交换 | 制造商名单 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |