MPC5601DXLL datasheet(40/77 Pages) FREESCALE

40 / 77 page

MPC5602D Microcontroller Data Sheet, Rev. 3.1

Preliminary—Subject to Change Without Notice

Electrical characteristics

Freescale Semiconductor

4.11

Flash memory electrical characteristics

The Data Flash operation depends strongly on the Code Flash operation. If Code Flash is switched-off, the Data Flash is

disabled.

4.11.1

Program/Erase characteristics

Table 23 shows the program and erase characteristics.

IDDSTDBY

CC P STANDBY mode current9 Slow internal RC oscillator

(128 kHz) running

TA =25°C

—

TBD

µA

DTA =55°C

—

TBD

—

DTA =85°C

—

DTA = 105 °C

—

PTA = 125 °C

—

TBD

1 V

DD = 3.3 V ± 10% / 5.0 V ± 10%, TA = 40 to 125 °C, unless otherwise specified

2 Running consumption is given on voltage regulator supply (V

DDREG). It does not include consumption linked to I/Os

toggling. This value is highly dependent on the application. The given value is thought to be a worst case value with

all peripherals running, and code fetched from Code Flash while modify operation on-going on Data Flash. Note that

this value can be significantly reduced by application: switch off not used peripherals (default), reduce peripheral

frequency through internal prescaler, fetch from SRAM most used functions, use low power mode when possible.

3 Higher current may be sinked by device during power-up and standby exit. Please refer to in rush current on Table 20.

4 RUN current measured with typical application with accesses on both Flash and SRAM.

5 Only for the “P” classification: Code fetched from SRAM: Serial IPs CAN and LIN in loop back mode, DSPI as Master,

PLL as system clock (4 x Multiplier) peripherals on (eMIOS/CTU/ADC) and running at max frequency, periodic

SW/WDG timer reset enabled.

6 Data Flash Power Down. Code Flash in Low Power. RC-OSC 128 kHz & RC-OSC 16 MHz on. 10 MHz XTAL clock.

FlexCAN: 0 ON (clocked but no reception or transmission). LINFlex: instances: 0, 1, 2 ON (clocked but no reception

or transmission), instance: 3 clocks gated. eMIOS: instance: 0 ON (16 channels on PA[0]–PA[11] and PC[12]–PC[15])

with PWM 20 kHz, instance: 1 clock gated. DSPI: instance: 0 (clocked but no communication). RTC/API ON.PIT ON.

STM ON. ADC ON but no conversion except 2 analog watchdogs.

7 Only for the “P” classification: No clock, RC-OSC 16 MHz off, RC-OSC 128 kHz on, PLL off, HPVreg off,

ULPVreg/LPVreg on. All possible peripherals off and clock gated. Flash in power down mode.

8 When going from RUN to STOP mode and the core consumption is > 6 mA, it is normal operation for the main

regulator module to be kept on by the on-chip current monitoring circuit. This is most likely to occur with junction

temperatures exceeding 125 °C and under these circumstances, it is possible for the current to initially exceed the

maximum STOP specification by up to 2 mA. After entering stop, the application junction temperature will reduce to

the ambient level and the main regulator will be automatically switched off when the load current is below 6 mA.

9 Only for the “P” classification: ULPVreg on, HP/LPVreg off, 16 KB SRAM on, device configured for minimum

consumption, all possible modules switched off.

Table 22. Low voltage power domain electrical characteristics (continued)

Symbol

Parameter

Conditions1

Value

Unit

Min

Typ

Max

MPC5601DXLL 数据表(PDF) 40 Page - Freescale Semiconductor, Inc

MPC5601DXLL 数据表(HTML) 40 Page - Freescale Semiconductor, Inc

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77

数据表下载