ADE7763ARSZ datasheet(19/56 Pages) AD

19 / 56 page

Data Sheet

ADE7763

Rev. C | Page 19 of 56

input. Reading the RSTVPEAK and RSTIPEAK registers clears

their respective contents after the read operation.

INTERRUPTS

Interrupts are managed through the interrupt status register

(STATUS[15:0]) and the interrupt enable register

(IRQEN[15:0]). When an interrupt event occurs, the

corresponding flag in the status register is set to Logic 1—see

the Interrupt Status Register section. If the enable bit for this

interrupt in the interrupt enable register is Logic 1, the IRQ

logic output will go active low. The flag bits in the status register

are set irrespective of the state of the enable bits.

To determine the source of the interrupt, the system master

(MCU) should perform a read from the status register with

reset (RSTSTATUS[15:0]). This is achieved by carrying out a

read from Address 0Ch. The IRQ output goes logic high after

the completion of the interrupt status register read command—

see the Interrupt Timing section. When carrying out a read

with reset, the ADE7763 is designed to ensure that no interrupt

events are missed. If an interrupt event occurs as the status

logic output will be guaranteed to go high for the duration of

the interrupt status register data transfer before going logic low

again to indicate the pending interrupt. See the next section for

a more detailed description.

Using Interrupts with an MCU

Figure 38 shows a timing diagram with a suggested imple-

mentation of ADE7763 interrupt management using an MCU.

At time t1, the IRQ line goes active low, indicating that one or

more interrupt events have occurred. Tie the IRQ logic output to

a negative edge-triggered external interrupt on the MCU.

Configure the MCU to start executing its interrupt service

routine (ISR) when a negative edge is detected on the IRQ line.

After entering the ISR, disable all interrupts by using the global

interrupt enable bit. At this point, the MCU IRQ external

interrupt flag can be cleared to capture interrupt events that

occur during the current ISR. When the MCU interrupt flag is

cleared, a read from the status register with reset is carried out.

This causes the IRQ line to reset to logic high (t2)—see the

Interrupt Timing section. The status register contents are used

to determine the source of the interrupt(s) and, therefore, the

appropriate action to be taken. If a subsequent interrupt event

occurs during the ISR, that event will be recorded by the MCU

external interrupt flag being set again (t3). Upon the completion

of the ISR, the global interrupt mask is cleared (same

instruction cycle) and the external interrupt flag causes the

MCU to jump to its ISR again. This ensures that the MCU does

not miss any external interrupts.

IRQ

GLOBAL

INTERRUPT

MASK SET

ISR RETURN

GLOBAL INTERRUPT

MASK RESET

CLEAR MCU

INTERRUPT

FLAG

READ

STATUS WITH

RESET (0x0C)

ISR ACTION

(BASED ON STATUS CONTENTS)

MCU

INTERRUPT

FLAG SET

MCU

PROGRAM

SEQUENCE

JUMP

ISR

JUMP

ISR

Figure 37. Interrupt Management

SCLK

DIN

DOUT

IRQ

t11

READ STATUS REGISTER COMMAND

STATUS REGISTER CONTENTS

DB7

DB0

Figure 38. Interrupt Timing

ADE7763ARSZ 数据表(PDF) 19 Page - Analog Devices

ADE7763ARSZ 数据表(HTML) 19 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56

数据表下载

链接网址

ADE7763ARSZ 数据表(PDF) 19 Page - Analog Devices

ADE7763ARSZ 数据表(HTML) 19 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56

数据表 下载

链接网址

数据表下载