I2CCON datasheet(59/210 Pages) MICROCHIP

59 / 210 page

DS70139G-page 59

dsPIC30F2011/2012/3012/3013

7.0

I/O PORTS

All of the device pins (except VDD, VSS, MCLR and

OSC1/CLKI) are shared between the peripherals and

the parallel I/O ports.

All I/O input ports feature Schmitt Trigger inputs for

improved noise immunity.

7.1

Parallel I/O (PIO) Ports

When a peripheral is enabled and the peripheral is

actively driving an associated pin, the use of the pin as

a general purpose output pin is disabled. The I/O pin

can be read, but the output driver for the parallel port bit

is disabled. If a peripheral is enabled, but the peripheral

is not actively driving a pin, that pin can be driven by a

port.

All port pins have three registers directly associated

with the operation of the port pin. The Data Direction

or an output. If the data direction bit is a ‘1’, then the pin

is an input. All port pins are defined as inputs after a

Reset. Reads from the latch (LATx), read the latch.

Writes to the latch, write the latch (LATx). Reads from

the port (PORTx), read the port pins and writes to the

port pins, write the latch (LATx).

Any bit and its associated data and Control registers

that are not valid for a particular device are disabled.

That means the corresponding LATx and TRISx

registers and the port pin read as zeros.

When a pin is shared with another peripheral or

function that is defined as an input only, it is

nevertheless regarded as a dedicated port because

there is no other competing source of outputs.

A parallel I/O (PIO) port that shares a pin with a

peripheral is, in general, subservient to the peripheral.

The peripheral’s output buffer data and control signals

are provided to a pair of multiplexers. The multiplexers

select whether the peripheral or the associated port

has ownership of the output data and control signals of

the I/O pad cell. Figure 7-1 illustrates how ports are

shared with other peripherals and the associated I/O

cell (pad) to which they are connected.

The format of the registers for the shared ports,

(PORTB, PORTC, PORTD and PORTF) are shown in

Table 7-1 through Table 7-6.

FIGURE 7-1:

BLOCK DIAGRAM OF A SHARED PORT STRUCTURE

Note:

This data sheet summarizes features of

this group of dsPIC30F devices and is not

intended to be a complete reference

source. For more information on the CPU,

peripherals,

descriptions

and

general device functionality, refer to the

“dsPIC30F Family Reference Manual”

(DS70046).

Note:

The actual bits in use vary between

devices.

WR LAT +

TRIS Latch

I/O Pad

WR Port

Data Bus

Data Latch

Read LAT

Read Port

Read TRIS

WR TRIS

Peripheral Output Data

Output Enable

Peripheral Input Data

I/O Cell

Peripheral Module

Peripheral Output Enable

PIO Module

Output Multiplexers

Output Data

Input Data

Peripheral Module Enable

I2CCON 数据表(PDF) 59 Page - Microchip Technology

I2CCON 数据表(HTML) 59 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表下载