I2CCON datasheet(73/210 Pages) MICROCHIP

73 / 210 page

DS70139G-page 73

dsPIC30F2011/2012/3012/3013

9.0

TIMER1 MODULE

This section describes the 16-bit general purpose

Timer1 module and associated operational modes.

Figure 9-1 depicts the simplified block diagram of the

16-bit Timer1 module. The following sections provide

detailed descriptions including setup and Control

registers, along with associated block diagrams for the

operational modes of the timers.

The Timer1 module is a 16-bit timer that serves as the

time counter for the real-time clock or operates as a

free-running interval timer/counter. The 16-bit timer has

the following modes:

• 16-bit Timer

• 16-bit Synchronous Counter

• 16-bit Asynchronous Counter

These operational characteristics are supported:

• Timer gate operation

• Selectable prescaler settings

• Timer operation during CPU Idle and Sleep

modes

• Interrupt on 16-bit Period register match or falling

edge of external gate signal

These operating modes are determined by setting the

appropriate bit(s) in the 16-bit SFR, T1CON. Figure 9-1

presents a block diagram of the 16-bit timer module.

16-bit Timer Mode: In the 16-bit Timer mode, the timer

increments on every instruction cycle up to a match

value preloaded into the Period register PR1, then

resets to ‘0’ and continues to count.

When the CPU goes into the Idle mode, the timer stops

incrementing unless the TSIDL (T1CON<13>) bit = 0.

If TSIDL = 1, the timer module logic resumes the incre-

menting sequence on termination of CPU Idle mode.

16-bit Synchronous Counter Mode: In the 16-bit

Synchronous Counter mode, the timer increments on

the rising edge of the applied external clock signal

which is synchronized with the internal phase clocks.

The timer counts up to a match value preloaded in PR1,

then resets to ‘0’ and continues.

When the CPU goes into the Idle mode, the timer stops

incrementing unless the respective TSIDL bit = 0. If

TSIDL = 1, the timer module logic resumes the

incrementing sequence upon termination of the CPU

Idle mode.

16-bit Asynchronous Counter Mode: In the 16-bit

Asynchronous Counter mode, the timer increments on

every rising edge of the applied external clock signal.

The timer counts up to a match value preloaded in PR1,

then resets to ‘0’ and continues.

When the timer is configured for the Asynchronous

mode of operation and the CPU goes into the Idle

mode, the timer stops incrementing if TSIDL = 1.

FIGURE 9-1:

16-BIT TIMER1 MODULE BLOCK DIAGRAM

Note:

This data sheet summarizes features of

this group of dsPIC30F devices and is not

intended to be a complete reference

source. For more information on the CPU,

peripherals,

descriptions

and

general device functionality, refer to the

“dsPIC30F Family Reference Manual”

(DS70046).

TON

Sync

SOSCI

SOSCO/

PR1

T1IF

Equal

Comparator x 16

TMR1

Reset

LPOSCEN

Event Flag

TSYNC

TGATE

TCKPS<1:0>

Prescaler

1, 8, 64, 256

TGATE

TCY

T1CK

1 x

0 1

0 0

Gate

Sync

I2CCON 数据表(PDF) 73 Page - Microchip Technology

I2CCON 数据表(HTML) 73 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表下载