I2CCON datasheet(20/210 Pages) MICROCHIP

20 / 210 page

dsPIC30F2011/2012/3012/3013

DS70139G-page 20

The core does not support a multi-stage instruction

pipeline. However, a single-stage instruction prefetch

mechanism is used, which accesses and partially

decodes instructions a cycle ahead of execution, in

order to maximize available execution time. Most

instructions execute in a single cycle with certain

exceptions.

The core features a vectored exception processing

structure for traps and interrupts, with 62 independent

vectors. The exceptions consist of up to 8 traps (of

which 4 are reserved) and 54 interrupts. Each interrupt

is prioritized based on a user-assigned priority between

1 and 7 (1 being the lowest priority and 7 being the

highest), in conjunction with a predetermined ‘natural

order’. Traps have fixed priorities ranging from 8 to 15.

2.2

Programmer’s Model

The programmer’s model is shown in Figure 2-1 and

consists of 16 x 16-bit working registers (W0 through

W15), 2 x 40-bit accumulators (ACCA and ACCB),

STATUS register (SR), Data Table Page register

(TBLPAG), Program Space Visibility Page register

(PSVPAG), DO and REPEAT registers (DOSTART,

DOEND, DCOUNT and RCOUNT) and Program Coun-

ter (PC). The working registers can act as data,

address or offset registers. All registers are memory

mapped. W0 acts as the W register for file register

addressing.

Some of these registers have a shadow register asso-

ciated with each of them, as shown in Figure 2-1. The

shadow register is used as a temporary holding register

and can transfer its contents to or from its host register

upon the occurrence of an event. None of the shadow

registers are accessible directly. The following rules

apply for transfer of registers into and out of shadows.

• PUSH.S and POP.S

W0, W1, W2, W3, SR (DC, N, OV, Z and C bits

only) are transferred.

• DO instruction

DOSTART, DOEND, DCOUNT shadows are

pushed on loop start and popped on loop end.

When a byte operation is performed on a working reg-

ister, only the Least Significant Byte (LSB) of the target

mapped working registers is that both the Least and

Most Significant Bytes (MSB) can be manipulated

through byte-wide data memory space accesses.

2.2.1

SOFTWARE STACK POINTER/

FRAME POINTER

The dsPIC® DSC devices contain a software stack.

W15 is the dedicated Software Stack Pointer (SP),

which

automatically

modified

exception

processing and subroutine calls and returns. However,

W15 can be referenced by any instruction in the same

manner as all other W registers. This simplifies the

reading, writing and manipulation of the Stack Pointer

(e.g., creating stack frames).

W15 is initialized to 0x0800 during a Reset. The user

may reprogram the SP during initialization to any

location within data space.

W14 has been dedicated as a Stack Frame Pointer, as

defined by the LNK and ULNK instructions. However,

W14 can be referenced by any instruction in the same

manner as all other W registers.

2.2.2

STATUS REGISTER

The dsPIC DSC core has a 16-bit STATUS register

(SR), the LSB of which is referred to as the SR Low

byte (SRL) and the MSB as the SR High byte (SRH).

See Figure 2-1 for SR layout.

SRL contains all the MCU ALU operation Status flags

(including the Z bit), as well as the CPU Interrupt

Priority Level Status bits, IPL<2:0>, and the Repeat

Active Status bit, RA. During exception processing,

SRL is concatenated with the MSB of the PC to form a

complete word value which is then stacked.

The upper byte of the STATUS register contains the

DSP Adder/Subtracter Status bits, the DO Loop Active

bit (DA) and the Digit Carry (DC) Status bit.

2.2.3

PROGRAM COUNTER

The program counter is 23 bits wide; bit 0 is always

clear. Therefore, the PC can address up to 4M

instruction words.

Note:

In order to protect against misaligned

stack accesses, W15<0> is always clear.

I2CCON 数据表(PDF) 20 Page - Microchip Technology

I2CCON 数据表(HTML) 20 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表下载