PIC16LC620-04SLASHSS datasheet(51/108 Pages) MICROCHIP

51 / 108 page

Preliminary

DS30235G-page 51

PIC16C62X

9.4.5

TIME-OUT SEQUENCE

On power-up the time-out sequence is as follows: First

PWRT time-out is invoked after POR has expired. Then

OST is activated. The total time-out will vary based on

oscillator conﬁguration and PWRTE bit status. For

example, in RC mode with PWRTE bit erased (PWRT

disabled), there will be no time-out at all. Figure 9-9,

Figure 9-10

and

Figure 9-11

depict

time-out

sequences.

Since the time-outs occur from the POR pulse, if MCLR

is kept low long enough, the time-outs will expire. Then

bringing MCLR high will begin execution immediately

(see Figure 9-10). This is useful for testing purposes or

to synchronize more than one PIC16C62X device oper-

ating in parallel.

Table 9-6 shows the reset conditions for some special

registers, while Table 9-7 shows the reset conditions for

all the registers.

9.4.6

POWER CONTROL (PCON)/

STATUS REGISTER

The power control/status register, PCON (address

8Eh) has two bits.

Bit0 is BOR (Brown-out). BOR is unknown on

power-on-reset. It must then be set by the user and

checked on subsequent resets to see if BOR = 0

indicating that a brown-out has occurred. The BOR

status bit is a don’t care and is not necessarily

predictable if the brown-out circuit is disabled (by

setting BOREN bit = 0 in the Conﬁguration word).

Bit1

POR

(Power-on-reset).

‘0’ on

power-on-reset and unaffected otherwise. The user

must write a ‘1’ to this bit following a power-on-reset.

On a subsequent reset if POR is ‘0’, it will indicate that

a power-on-reset must have occurred (VDD may have

gone too low).

TABLE 9-3:

TIME-OUT IN VARIOUS SITUATIONS

TABLE 9-4:

STATUS/PCON BITS AND THEIR SIGNIFICANCE

Legend: u = unchanged, x = unknown

Oscillator Conﬁguration

Power-up

Brown-out Reset

Wake-up

from SLEEP

PWRTE = 0

PWRTE = 1

XT, HS, LP

72 ms + 1024 TOSC

1024 TOSC

72 ms + 1024 TOSC

1024 TOSC

72 ms

—

72 ms

—

POR

BOR

Power-on-reset

Illegal, TO is set on POR

Illegal, PD is set on POR

Brown-out Reset

WDT Reset

WDT Wake-up

MCLR reset during normal operation

MCLR reset during SLEEP

TABLE 9-5:

SUMMARY OF REGISTERS ASSOCIATED WITH BROWN-OUT

Address

Name

Bit 7

Bit 6

Bit 5

Bit 4

Bit 3

Bit 2

Bit 1

Bit 0

Value on POR

Reset

Value on all

other resets(1)

83h

STATUS

0001 1xxx

000q quuu

8Eh

PCON

—

POR

BOR

---- --0x

---- --uq

Note1: Other (non power-up) resets include MCLR reset, Brown-out Reset and Watchdog Timer Reset during normal operation.

PIC16LC620-04/SS 数据表(PDF) 51 Page - Microchip Technology

PIC16LC620-04/SS 数据表(HTML) 51 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表下载