PIC16LC620-04SLASHSS datasheet(9/108 Pages) MICROCHIP

9 / 108 page

Preliminary

DS30235G-page 9

PIC16C62X

3.0

ARCHITECTURAL OVERVIEW

The high performance of the PIC16C62X family can be

attributed to a number of architectural features

commonly found in RISC microprocessors. To begin

with, the PIC16C62X uses a Harvard architecture, in

which, program and data are accessed from separate

memories using separate busses. This improves

bandwidth over traditional von Neumann architecture

where program and data are fetched from the same

memory. Separating program and data memory further

allows instructions to be sized differently than 8-bit

wide data word. Instruction opcodes are 14-bits wide

making it possible to have all single word instructions.

A 14-bit wide program memory access bus fetches a

14-bit instruction in a single cycle. A two-stage pipeline

overlaps

fetch

and

execution

instructions.

Consequently, all instructions (35) execute in a sin-

gle-cycle (200 ns @ 20 MHz) except for program

branches.

The PIC16C620A and PIC16CR620A address 512 x

14 on-chip program memory. The PIC16C621(A)

addresses

program

memory.

The

PIC16C622(A) addresses 2K x 14 program memory.

All program memory is internal.

The PIC16C62X can directly or indirectly address its

registers including the program counter are mapped in

the data memory. The PIC16C62X have an orthogonal

(symmetrical) instruction set that makes it possible to

carry out any operation on any register using any

addressing mode. This symmetrical nature and lack of

‘special optimal situations’ make programming with the

PIC16C62X simple yet efﬁcient. In addition, the

learning curve is reduced signiﬁcantly.

The PIC16C62X devices contain an 8-bit ALU and

working register. The ALU is a general purpose

arithmetic unit. It performs arithmetic and Boolean

functions between data in the working register and any

The ALU is 8-bit wide and capable of addition,

subtraction, shift and logical operations. Unless

otherwise mentioned, arithmetic operations are two's

complement in nature. In two-operand instructions,

typically

one

operand

the

working

(W register). The other operand is a ﬁle register or an

immediate constant. In single operand instructions, the

operand is either the W register or a ﬁle register.

The W register is an 8-bit working register used for ALU

operations. It is not an addressable register.

Depending on the instruction executed, the ALU may

affect the values of the Carry (C), Digit Carry (DC), and

Zero (Z) bits in the STATUS register. The C and DC bits

operate as a Borrow and Digit Borrow out bit,

respectively, bit in subtraction. See the SUBLW and

SUBWF

instructions for examples.

A simpliﬁed block diagram is shown in Figure 3-1, with

a description of the device pins in Table 3-1.

PIC16LC620-04/SS 数据表(PDF) 9 Page - Microchip Technology

PIC16LC620-04/SS 数据表(HTML) 9 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表下载