ADBMS1818ASWZ-R7 datasheet(65/89 Pages) AD

65 / 89 page

Data Sheet

ADBMS1818

MEMORY MAP

analog.com

Rev. 0 | 65 of 89

Table 70. Memory Map Bit Descriptions

Time

left

(mi-

nutes

)

Disa-

bled

time-

out

0 to

0.5

0.5 to

1 to 2 2 to 3 3 to 4 4 to 5 5 to

10 to

15 to

20 to

30 to

40 to

60 to

75 to

90 to

120

MUTE

Mute status (read on-

ly)

1: mute is activated and discharging is disabled

0: mute is deactivated

FDRF

Force digital redun-

dancy failure

1: forces the digital redundancy comparison for ADC conversions to fail

0: enables the normal redundancy comparison

PS,

Bits[1:0]

Digital redundancy

path selection

11: redundancy is applied only to the ADC3 digital path

10: redundancy is applied only to the ADC2 digital path

01: redundancy is applied only to the ADC1 digital path

00: redundancy is applied sequentially to the ADC1, ADC2, and ADC3 digital paths during cell conversions and applied to ADC1 during

AUX and STATUS conversions

DTMEN

Enable discharge tim-

er monitor

1: enables the discharge timer monitor function if the DTEN pin is asserted

0: disables the discharge timer monitor function. The normal discharge timer function is enabled if the DTEN pin is asserted

CxV

Cell x voltage1

x = 1 to 18

16-bit ADC measurement value for Cell x

Cell voltage for Cell x = CxV × 100 μV

CxV is rest to 0xFFFF on power-up and after clear command

GxV

GPIO x voltage1

x = 1 to 9

16-bit ADC measurement value for GPIOx

Voltage for GPIOx = GxV × 100 μV

GxV is reset to 0xFFFF on power-up and after clear command

REF

2nd reference volt-

age1

16-bit ADC measurement value for 2nd reference

Sum of all cells meas-

urement1

16-bit ADC measurement value of the sum of all cell voltages, sum of all cells voltage = SC × 100 μV × 30

ITMP

Internal die tempera-

ture1

16-bit ADC measurement value of the internal die temperature, temperature measurement voltage = ITMP × 100 μV/7.6mV/°C − 276°C

Analog power supply

voltage1

16-bit ADC measurement value of the analog power supply voltage, analog power supply voltage = VA × 100 μV, the value of VA is set by

external components that must be in the range of 4.5 V to 5.5 V for normal operation

Digital power supply

voltage1

16-bit ADC measurement value of the digital power supply voltage, digital power supply voltage = VD × μV, normal range is within 2.7 V

to 3.6 V

CxOV

Cell x overvoltage flag x = 1 to 18

Cell voltage compared to VOV comparison voltage

0: Cell x not flagged for overvoltage condition

1: Cell x flagged

CxUV

Cell x undervoltage

flag

x = 1 to 18

Cell voltage compared to VUV comparison voltage

0: Cell x not flagged for overvoltage condition

1: Cell x flagged

ADBMS1818ASWZ-R7 数据表(PDF) 65 Page - Analog Devices

ADBMS1818ASWZ-R7 数据表(HTML) 65 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89

数据表下载